Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Testing Of Face Milled Spiral Bevel Gears At High Speed And Load
Download Testing Of Face Milled Spiral Bevel Gears At High Speed And Load full books in PDF, epub, and Kindle. Read online Testing Of Face Milled Spiral Bevel Gears At High Speed And Load ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Testing of Face-Milled Spiral Bevel Gears at High-Speed and Load by :
Download or read book Testing of Face-Milled Spiral Bevel Gears at High-Speed and Load written by and published by . This book was released on 2001 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt: Spiral bevel gears are an important drive system components of rotorcraft (helicopters) currently in use. In this application the spiral bevel gears are required to transmit very high torque at high rotational speed. Available experimental data on the operational characteristics for thermal and structural behavior is relatively small in comparison to that found for parallel axis gears. An ongoing test program has been in place at NASA Glenn Research Center over the last ten years to investigate their operational behavior at operating conditions found in aerospace applications. This paper will summarize the results of the tests conducted on face-milled spiral bevel gears. The data from the pinion member (temperature and stress) were taken at conditions from slow-roll to 14400 rpm and up to 537 kW (720 hp). The results have shown that operating temperature is affected by the location of the lubricating jet with respect to the point it is injected and the operating conditions that are imposed. Also the stress measured from slow-roll to very high rotational speed, at various torque levels, indicated little dynamic affect over the rotational speeds tested.
Book Synopsis TESTING OF FACE-MILLED SPIRAL BEVEL GEARS AT HIGH-SPEED AND LOAD... NASA/TM-2001-210743... JUN. 20, 2001 by :
Download or read book TESTING OF FACE-MILLED SPIRAL BEVEL GEARS AT HIGH-SPEED AND LOAD... NASA/TM-2001-210743... JUN. 20, 2001 written by and published by . This book was released on 2002 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Experimental Comparison of Face-Milled and Face-Hobbed Spiral Bevel Gears by :
Download or read book Experimental Comparison of Face-Milled and Face-Hobbed Spiral Bevel Gears written by and published by . This book was released on 2001 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental comparison of face-milled and face-hobbed spiral bevel gears was accomplished. The two differently manufactured spiral bevel gear types were tested in a closed-loop facility at NASA Glenn Research Center. Strain, vibration, and noise testing were completed at various levels of rotational speed and load. Tests were conducted from static (slow-roll) to 12600 rpm and up to 269 N.m (2380 in.lb) pinion speed and load conditions. The tests indicated that the maximum stress recorded at the root locations had nearly the same values, however the stress distribution was different from the toe to the heel. Also. the alternating stress measured was higher for the face-milled pinion than that attained for the face-bobbed pinion (larger minimum stress). The noise and vibration results indicated that the levels measured for the face-bobbed components were less than those attained for the face-milled gears tested.
Book Synopsis Experimental Testing of Prototype Face Gears for Helicopter Transmissions by :
Download or read book Experimental Testing of Prototype Face Gears for Helicopter Transmissions written by and published by . This book was released on 1992 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental program to test the feasibility of using face gears in a high-speed and high-power environment was conducted. Four face gear sets were tested, two sets at a time, in a closed-loop test stand at pinion rotational speeds to 19,100 rpm and to 271 kW (364 hp). The test gear sets were one-half scale of the helicopter design gear set. Testing the gears at one- eighth power, the test gear set had slightly increased bending and compressive stresses when compared to the full scale design. The tests were performed in the NASA Lewis spiral bevel gear test facility. All four sets of gears successfully ran at 100 percent of design torque and speed for 30 million pinion cycles, and two sets successfully ran at 200 percent of torque for an additional 30 million pinion cycles. The results, although limited, demonstrated the feasibility of using face gears for high-speed, high-load applications.
Book Synopsis Experimental and Analytical Assessment of the Thermal Behavior of Spiral Bevel Gears by : Robert F. Handschuh
Download or read book Experimental and Analytical Assessment of the Thermal Behavior of Spiral Bevel Gears written by Robert F. Handschuh and published by . This book was released on 1995 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Comparison of Experimental and Analytical Tooth Bending Stress of Aerospace Spiral Bevel Gears by :
Download or read book Comparison of Experimental and Analytical Tooth Bending Stress of Aerospace Spiral Bevel Gears written by and published by . This book was released on 1999 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study to investigate the bending stress in aerospace-quality spiral bevel gears was performed. Tests were conducted in the NASA Lewis Spiral Bevel Gear Test Facility. Multiple teeth on the spiral bevel pinion were instrumented with strain gages and tests were conducted from static (slow roll) to 14400 RPM at power levels to 540kW (720 hp). Effects of changing speed and load on the bending stress were measured. Experimental results are compared to those found by three-dimensional finite element analysis.
Book Synopsis Experimental Evaluation of Face Gears for Aerospace Drive System Applications by :
Download or read book Experimental Evaluation of Face Gears for Aerospace Drive System Applications written by and published by . This book was released on 1996 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Research & Technology 2001 written by and published by DIANE Publishing. This book was released on with total page 251 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Evaluation of Carburized and Ground Face Gears by :
Download or read book Evaluation of Carburized and Ground Face Gears written by and published by . This book was released on 1999 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: Experimental durability tests were performed on carburized and ground AISI 9310 steel face gears. The tests were in support of a Defense Advanced Research Projects Agency (DARPA) Technology Reinvestment Program (TRP) to enhance face-gear technology. The tests were conducted in the NASA Glenn spiral-bevel-gear/face-gear test facility. Tests were run at 2300 rpm face gear speed and at loads of 64, 76, 88, 100, and 112-percent of the design torque of 377 N-m (3340 in-lb). The carburized and ground face gears demonstrated the required durability when run for ten-million cycles at each of the applied loads. Proper installation was critical for the successful operation of the spur pinions and face gears. A large amount of backlash produced tooth contact patterns that approached the inner-diameter edge of the face-gear tooth. Low backlash produced tooth contact patterns that approached the outer-diameter edge of the face-gear tooth. Measured backlashes in the range of 0.178 to 0.254 mm (0.007 to 0.010 in) produced acceptable tooth contact patterns.
Book Synopsis Design, Generation, Stress Analysis and Test of Low-Noise, Increased Strength Face-Milled Spiral Bevel Gears by : Faydor L. Litvin
Download or read book Design, Generation, Stress Analysis and Test of Low-Noise, Increased Strength Face-Milled Spiral Bevel Gears written by Faydor L. Litvin and published by . This book was released on 1997-10-01 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Friction, Lubrication and Wear by : Mohammad Asaduzzaman Chowdhury
Download or read book Friction, Lubrication and Wear written by Mohammad Asaduzzaman Chowdhury and published by BoD – Books on Demand. This book was released on 2019-10-30 with total page 226 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tribology has rapidly expanded in recent years as the demand for improved materials has increased. The good function of numerous electrical, electrochemical, mechanical, and biological systems or components depends on suitable friction, lubrication, and wear as well as tribological values. In this context, the study of friction, wear, and lubrication is of tremendous pragmatic importance. The reduction of friction and loss of materials in relative motion are important challenges to improveing energy efficiency. This book guides the rational design of material for technological application. Chapters cover topics such as the resistance of dry abrasive wear, the role of a brand-new additive in the minimization of friction and wear, the structural-energy model of elastic-plastic deformation, the influence of micro-abrasive wear modes, tribological characteristics of magneto-rheological fluids (MRFs) and magneto-rheological elastomers (MREs), and different treatment technologies to improve tribological properties, among others.
Book Synopsis Computerized Design and Analysis of Face-Milled, Uniform Tooth Height Spiral Bevel Gear Drives by : Faydor L. Litvin
Download or read book Computerized Design and Analysis of Face-Milled, Uniform Tooth Height Spiral Bevel Gear Drives written by Faydor L. Litvin and published by . This book was released on 1996 with total page 14 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Author :National Aeronautics and Space Adm Nasa Publisher :Independently Published ISBN 13 :9781723998676 Total Pages :34 pages Book Rating :4.9/5 (986 download)
Book Synopsis Comparison of Experimental and Analytical Tooth Bending Stress of Aerospace Spiral Bevel Gears by : National Aeronautics and Space Adm Nasa
Download or read book Comparison of Experimental and Analytical Tooth Bending Stress of Aerospace Spiral Bevel Gears written by National Aeronautics and Space Adm Nasa and published by Independently Published. This book was released on 2018-09-25 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt: An experimental study to investigate the bending stress in aerospace-quality spiral bevel gears was performed. Tests were conducted in the NASA Lewis Spiral Bevel Gear Test Facility. Multiple teeth on the spiral bevel pinion were instrumented with strain gages and tests were conducted from static (slow roll) to 14400 RPM at power levels to 540kW (720 hp). Effects of changing speed and load on the bending stress were measured. Experimental results are compared to those found by three-dimensional finite element analysis. Handschuh, Robert F. and Bibel, George D. Glenn Research Center NASA/TM-1999-208903, NAS 1.15:208903, E-11365-1, ARL-TR-1891
Book Synopsis Experimental Comparison of Face-milled and Face-hobbed Spiral Bevel Gears ... Nasa by : United States. National Aeronautics and Space Administration
Download or read book Experimental Comparison of Face-milled and Face-hobbed Spiral Bevel Gears ... Nasa written by United States. National Aeronautics and Space Administration and published by . This book was released on 2003* with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Local Synthesis and Tooth Contact Analysis of Face-milled Spiral Bevel Gears by : Faydor L. Litvin
Download or read book Local Synthesis and Tooth Contact Analysis of Face-milled Spiral Bevel Gears written by Faydor L. Litvin and published by . This book was released on 1991 with total page 204 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis How to Determine Spiral Bevel Gear Tooth Geometry for Finite Element Analysis by :
Download or read book How to Determine Spiral Bevel Gear Tooth Geometry for Finite Element Analysis written by and published by . This book was released on 1991 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: An analytical method has been developed to determine gear tooth surface coordinates of face milled spiral bevel gears. The method combines the basic gear design parameters with the kinematical aspects for spiral bevel gear manufacturing. A computer program was developed to calculate the surface coordinates. From this data a three dimensional model for finite element analysis can be determined. Development of the modeling method and an example case are presented. Spiral bevel gears are currently used in all helicopter power transmission systems. This type of gear is required to turn the corner from a horizontal engine to the vertical rotor shaft. These gears carry large loads and operate at high rotational speeds. Recent research has focused on understanding many aspects of spiral bevel gear operation, including gear geometry, gear dynamics, lubrication, stress analysis and measurement, misalignment, and coordinate measurements, as well as other areas.
Author :National Aeronautics and Space Administration (NASA) Publisher :Createspace Independent Publishing Platform ISBN 13 :9781722618063 Total Pages :52 pages Book Rating :4.6/5 (18 download)
Book Synopsis Local Synthesis and Tooth Contact Analysis of Face-Milled, Uniform Tooth Height Spiral Bevel Gears by : National Aeronautics and Space Administration (NASA)
Download or read book Local Synthesis and Tooth Contact Analysis of Face-Milled, Uniform Tooth Height Spiral Bevel Gears written by National Aeronautics and Space Administration (NASA) and published by Createspace Independent Publishing Platform. This book was released on 2018-07-08 with total page 52 pages. Available in PDF, EPUB and Kindle. Book excerpt: Face-milled spiral bevel gears with uniform tooth height are considered. An approach is proposed for the design of low-noise and localized bearing contact of such gears. The approach is based on the mismatch of contacting surfaces and permits two types of bearing contact either directed longitudinally or across the surface to be obtained. Conditions to avoid undercutting were determined. A Tooth Contact Analysis (TCA) was developed. This analysis was used to determine the influence of misalignment on meshing and contact of the spiral bevel gears. A numerical example that illustrates the theory developed is provided. Litvin, F. L. and Wang, A. G. Glenn Research Center...
