Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Electrochemical Dissolution Of Spent Ebr Ii Driver Fuel In Molten Salt Electrolyte
Download Electrochemical Dissolution Of Spent Ebr Ii Driver Fuel In Molten Salt Electrolyte full books in PDF, epub, and Kindle. Read online Electrochemical Dissolution Of Spent Ebr Ii Driver Fuel In Molten Salt Electrolyte ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Electrochemical Dissolution of Spent EBR-II Driver Fuel in Molten Salt Electrolyte by : R. W. Benedict
Download or read book Electrochemical Dissolution of Spent EBR-II Driver Fuel in Molten Salt Electrolyte written by R. W. Benedict and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Pyrochemical processing is a promising technology for closing the nuclear fuel cycle for next generation nuclear reactors. At Idaho National Laboratory (INL), such a pyrochemical process has been implemented for the treatment of spent fuel from the Experimental Breeder Reactor (EBR-II). A successful demonstration of the technology was performed from 1996 to 1999 for the Department of Energy (DOE). Since 2002, processing of the spent fuel andassociated research and development activities have been carried out under DOE's Advanced Fuel Cycle Initiative (AFCI) program. Electrorefining is considered to be the signature or central technology for pyrochemicalprocessing. This paper summarizes recent experience and results in electrorefining, specifically focusing on electrochemical dissolution of spent EBR-II driver fuel in the Mark-IV (Mk-IV) electrorefiner (ER).
Book Synopsis Initial Results for Electrochemical Dissolution of Spent EBR-II Fuel by :
Download or read book Initial Results for Electrochemical Dissolution of Spent EBR-II Fuel written by and published by . This book was released on 1998 with total page 11 pages. Available in PDF, EPUB and Kindle. Book excerpt: Initial results are reported for the anode behavior of spent metallic nuclear fuel in an electrorefining process. The anode behavior has been characterized in terms of the initial spent fuel composition and the final composition of the residual cladding hulls. A variety of results have been obtained depending on the experimental conditions. Some of the process variables considered are average and maximum cell voltage, average and maximum anode voltage, amount of electrical charge passed (coulombs or amp-hours) during the experiment, and cell resistance. The main goal of the experiments has been the nearly complete dissolution of uranium with the retention of zirconium and noble metal fission products in the cladding hulls. Analysis has shown that the most indicative parameters for determining an endpoint to the process, recognizing the stated goal, are the maximum anode voltage and the amount of electrical charge passed. For the initial experiments reported here, the best result obtained is greater than 98% uranium dissolution with approximately 50% zirconium retention. Noble metal fission product retention appears to be correlated with zirconium retention.
Book Synopsis Electrometallurgical Techniques for DOE Spent Fuel Treatment by : National Research Council
Download or read book Electrometallurgical Techniques for DOE Spent Fuel Treatment written by National Research Council and published by National Academies Press. This book was released on 2000-08-11 with total page 128 pages. Available in PDF, EPUB and Kindle. Book excerpt: The Committee on Electrometallurgical Techniques for DOE Spent Fuel Treatment was formed in September 1994 in response to a request made to the National Research Council (NRC) by the U.S. Department of Energy DOE. DOE requested an evaluation of electrometallurgical processing technology proposed by Argonne National Laboratory (ANL) for the treatment of DOE spent nuclear fuel. Electrometallurgical treatment of spent reactor fuel involves a set of operations designed to remove the remaining uranium metal and to incorporate the radioactive nuclides into well defined and reproducible waste streams. Over the course of the committee's operating life, this charge has remained constant. Within the framework of this overall charge, the scope of the committee's workâ€"as defined by its statement of taskâ€"has evolved in response to further requests from DOE, as well as technical accomplishments and regulatory and legal considerations. As part of its task, the committee has provided periodic assessments of ANL's R&D program on the electrometallurgical technology. Electrometallurgical Techniques for DOE Spent Fuel Treatment assesses the viability of electrometallurgical technology for treating DOE spent nuclear fuel and monitors the scientific and technical progress of the ANL program on electrometallurgical technology, specifically within the context of ANL's demonstration project on electrometallurgical treatment of EBR-II SNF. This report evaluates ANL's performance relative to the success criteria for the demonstration project, which have served as the basis for judging the efficacy of using electrometallurgical technology for the treatment of EBR-II spent nuclear fuel. It also addresses post-demonstration activities related to ANL's electrometallurgical demonstration project, and makes related recommendations in this area.
Book Synopsis Electrometallurgical Treatment of Aluminum-matrix Fuels by :
Download or read book Electrometallurgical Treatment of Aluminum-matrix Fuels written by and published by . This book was released on 1996 with total page 6 pages. Available in PDF, EPUB and Kindle. Book excerpt: The electrometallurgical treatment process described in this paper builds on our experience in treating spent fuel from the Experimental Breeder Reactor (EBR-II). The work is also to some degree, a spin-off from applying electrometallurgical treatment to spent fuel from the Hanford single pass reactors (SPRs) and fuel and flush salt from the Molten Salt Reactor Experiment (MSRE) in treating EBR-II fuel, we recover the actinides from a uranium-zirconium fuel by electrorefining the uranium out of the chopped fuel. With SPR fuel, uranium is electrorefined out of the aluminum cladding. Both of these processes are conducted in a LiCl-KCl molten-salt electrolyte. In the case of the MSRE, which used a fluoride salt-based fuel, uranium in this salt is recovered through a series of electrochemical reductions. Recovering high-purity uranium from an aluminum-matrix fuel is more challenging than treating SPR or EBR-II fuel because the aluminum- matrix fuel is typically -90% (volume basis) aluminum.
Book Synopsis EBR-II Spent Fuel Treatment Demonstration Project by :
Download or read book EBR-II Spent Fuel Treatment Demonstration Project written by and published by . This book was released on 1997 with total page 7 pages. Available in PDF, EPUB and Kindle. Book excerpt: For approximately 10 years, Argonne National Laboratory was developed a fast reactor fuel cycle based on dry processing. When the US fast reactor program was canceled in 1994, the fuel processing technology, called the electrometallurgical technique, was adapted for treating unstable spent nuclear fuel for disposal. While this technique, which involves electrorefining fuel in a molten salt bath, is being developed for several different fuel categories, its initial application is for sodium-bonded metallic spent fuel. In June 1996, the Department of Energy (DOE) approved a radiation demonstration program in which 100 spent driver assemblies and 25 spent blanket assemblies from the Experimental Breeder Reactor-II (EBR-II) will be treated over a three-year period. This demonstrated will provide data that address issues in the National Research Council's evaluation of the technology. The planned operations will neutralize the reactive component (elemental sodium) in the fuel and produce a low enriched uranium product, a ceramic waste and a metal waste. The fission products and transuranium elements, which accumulate in the electrorefining salt, will be stabilized in the glass-bonded ceramic waste form. The stainless steel cladding hulls, noble metal fission products, and insoluble residues from the process will be stabilized in a stainless steel/zirconium alloy. Upon completion of a successful demonstration and additional environmental evaluation, the current plans are to process the remainder of the DOE sodium bonded fuel.
Book Synopsis V siti︠a︡kh miz︠h︡narodnikh zmovnykiv by : John Hladun
Download or read book V siti︠a︡kh miz︠h︡narodnikh zmovnykiv written by John Hladun and published by . This book was released on 1963 with total page 32 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Electrochemical Recovery of Rare Earth Elements in Molten Salt Systems by : Stephanie Castro Baldivieso
Download or read book Electrochemical Recovery of Rare Earth Elements in Molten Salt Systems written by Stephanie Castro Baldivieso and published by . This book was released on 2024 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fission products are generated from the production of nuclear energy via the nuclear fission of uranium atoms. Used nuclear fuel (UNF) constitutes of fission products, where U and Pu isotopes represent the majority, and a small portion of this fuel contains actinides, rare-earth elements, and alkaline earth elements. The UNF is not recycled: it is stored in cooling pools due to its heat emanation and radioactivity from the actinides, and later it is kept in dry casting underground storage. Pyroprocessing of UNF allows the recycling of U and Pu from the waste, and it consists of 4 different stages: (1) oxide reduction unit, (2) electro refiner, (3) cathode processor and (4) fuel fabrication furnace. In the first stage, the oxide reduction unit, the UNF oxide gets reduced to metal at the cathode in molten LiCl-Li2O. This process is feasible for most of the fission products in the molten salt. However, rare-earths are very stable in their oxide form (e.g., Nd2O3) in chloride salts and it is very challenging to reduce them to metal. Electrochemical recovery and reduction pathways in which rare earth oxides (e.g., La2O3) can be readily reduced are investigated in this dissertation by mixing these oxides with transition metal oxides (e.g., NiO). At first, the feasibility of reducing transition metal oxides (e.g., NiO) was evaluated to characterize the standard reduction potentials and how efficient the transition metal oxide can be reduced in molten LiCl-Li2O electrolyte at 650 °C. Secondly, NiO was mixed with La2O3 respectively, using their atomic ratios (1:5) according to its phase diagram (La-Ni) and sintered into pellet materials. Furthermore, the reduction pathways of this alloy by electrolysis were investigated in LiCl, and LiCl-Li2O. In the next stage of the pyroprocess, the metallic UNF is used in the electrorefiner as the anode, and it is dissolved into a LiCl-KCl molten salt electrolyte, which allows the recovery of U and Pu at the cathode using an inert metal rod. However, the process becomes inefficient over time due to the accumulation of impurities (e.g., remaining fission products) in the molten salt electrolyte. The accumulation of these impurities reduces the recovery efficiency of U over time. The recovery of the rare earth fission products from the molten LiCl-KCl-RECl3 electrolyte used in the electrorefiner unit is investigated in this dissertation by evaluating the recovery efficiency of rare earth elements (specifically Gd) using liquid metal electrodes (e.g., Bi). At first, thermodynamic properties of Gd-Bi were determined using electromotive force (emf) measurements, in which enthalpies, entropies, activity and activity coefficients of Gd-Bi alloys were evaluated. The inconsistencies of the Gd-Bi phase diagrams were also evaluated using x-ray diffraction (XRD), differential scanning calorimetry (DSC) and coulometric titrations to examine the solubility of Gd in liquid Bi. The low activity of Gd-Bi alloys indicate strong interactions between the rare earths and liquid metals, and the kinetic properties (e.g., diffusivity, coulombic efficiencies, resistances) probed by electrochemical impedance spectroscopy (EIS), cyclic voltammetry, and deposition-removal cycles suggest a reversible process of Gd(III) ions in the molten LiCl-KCl-GdCl3 salt using an inert cathode; and Gd(III) ions maintain a constant ohmic and charge transfer resistances when deposited into Bi at different range of temperatures. This work will provide fundamental knowledge on how rare earth oxides can be reduced in a feasible manner to metals by alloy formation with transition metals, and how feasible is to recover Gd using liquid Bi electrode by studying its thermodynamic and kinetic properties in the molten salt electrolyte. Rare earth oxide reduction also provides cheaper alternatives to fabricate alloy systems used in Ni-metal hydride batteries (LaNi5 alloys).
Book Synopsis EBR-II Spent Fuel Treatment Demonstration Project Status by :
Download or read book EBR-II Spent Fuel Treatment Demonstration Project Status written by and published by . This book was released on 1998 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt: The application of electrometallurgical technology to spent nuclear fuel treatment is being demonstrated by treating 410 kg uranium spent driver fuel and 1,200 kg uranium spent blanket fuel from the Experimental Breeder Reactor-II (EBR-II) spent driver and blanket fuel. This fuel is a metallic uranium alloy and contains elemental sodium, which is a reactive material. Since reactive material is considered hazardous by US Environmental Protection Agency regulations, this fuel requires treatment before disposal in a geologic repository. The EBR-II spent fuel treatment demonstration conditions this fuel in an integrated process where the fuel is converted into three different products: low enriched uranium (LEU), ceramic waste and metallic waste. This demonstration was initiated in June 1996 and has treated approximately 50% of the driver fuel. The higher throughput equipment that will be used for blanket treatment processes has been installed in the hot cell facility and is being tested with depleted uranium. Metal waste forms have been produced from the irradiated metals from the driver fuel. Ceramic waste process equipment has been built and is being tested before installation in the hot cell facilities. This paper discusses the processes and the current results from the first 20 months of operation.
Book Synopsis First Electrolytic Dissolution Campaign of EBR-II Fuel at ICPP by : W. J. Bjorklund
Download or read book First Electrolytic Dissolution Campaign of EBR-II Fuel at ICPP written by W. J. Bjorklund and published by . This book was released on 1974 with total page 56 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first campaign using the electrolytic dissolution facility at the Idaho Chemical Processing Plant (ICPP) was completed during 1973. Several forms of EBR-II fuel containing highly-enriched uranium were dissolved in nitric acid in the electric field of the dissolver. Gadolinium, as a soluble nuclear poison, was used to guarantee nuclear safety in the headend processing equipment.
Book Synopsis A Study of Continuous Electrochemical Processing Operation Feasibility for Spent Nuclear Fuel by :
Download or read book A Study of Continuous Electrochemical Processing Operation Feasibility for Spent Nuclear Fuel written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Several methods of reprocessing are currently available to separate recyclable materials from spent nuclear fuel. Electrochemical processing, also known as pyroprocessing, represents a non-aqueous method of reprocessing that uses high temperature molten-salt based electrochemical technology. This method provides several advantages over conventional aqueous processing with respect to proliferation resistance. With electrochemical processing there is no pure plutonium separation and the presence of large decay heat and high radiation barriers dissuades diversion attempts. As the current electrochemical processing relies on a batch operation, the total throughput of the system is inherently limited and nuclear materials accounting is difficult due to the nonhomogeneous nature of the process. This results in much larger uncertainties in the total amount of material processed compared to the aqueous UREX+ or PUREX processes. Continuous electrochemical processing was considered as a way to address these concerns. The objective of this research was to investigate the feasibility of a continuous electrochemical processing operation to achieve the desired separation performance by using computer based simulation. The conceptual design of the continuous electrochemical processing includes two separate stages in a molten salt medium. First, a pure uranium deposit is collected at a solid cathode during the uranium extraction stage. When the amount of plutonium in electrorefiner becomes comparable or higher than the amount of uranium in the electrorefiner, a liquid cathode is employed to extract both uranium and plutonium in the second stage. In this approach, molten salt, as the material carrier, flows through the electrorefiner while chopped spent fuel is continuously fed into the system. Simulations of electrochemical reactions at the electrode surfaces were based on the kinetic modeling capability of a time-dependent code, REFIN. Based on a screening study performed for the.
Book Synopsis Proceedings of the Embedded Topical Meeting on DOE Spent Nuclear Fuel and Fissile Material Management, San Diego, California, June 4-8, 2000 by :
Download or read book Proceedings of the Embedded Topical Meeting on DOE Spent Nuclear Fuel and Fissile Material Management, San Diego, California, June 4-8, 2000 written by and published by . This book was released on 2000 with total page 556 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Integrated Electrorefining Efficiency Test for Pyrochemical Fuel Cycle by : T. A. Johnson
Download or read book Integrated Electrorefining Efficiency Test for Pyrochemical Fuel Cycle written by T. A. Johnson and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Pyrochemical processing plays an important role in the development of next generation nuclear reactors and closed nuclear fuel cycle technology. The Idaho National Laboratory (INL) has implemented a pyrochemical process for the treatment of sodium-bonded spent fuel from the Experimental Breeder Reactor-II (EBR-II). A successful demonstration of the technology was performed from 1996 to 1999 for the Department of Energy (DOE) [1]. Processing of the spent fuel and associated research and development activities have been integrated into DOE's Advanced Fuel Cycle Initiatives (AFCI) program since 2003. Electrorefining can be considered to be the signature or central technology for pyrochemical processing. In order to assess the efficiencies involved in the electrorefining process, an integrated electrorefining efficiency test was performed in the Mk-IV electrorefiner. This paper summarizes the observations and results obtained from the test. EXPERIMENT AND RESULTS The primary goal of the integrated processing efficiency test is to demonstrate the integrated actinide dissolution and recovery efficiencies typical for the fixed operating parameters that have been applied to Mk-IV electrorefiner (ER) and cathode processor (CP) to treat spent EBR-II driver fuel during the last three years. The findings are of importance for scaling-up the pyroprocess to recover and recycle valuable actinides from spent nuclear fuel. The test was performed in the Mk-IV electrorefiner. The ER is located in the hot cell of the Fuel Conditioning Facility at the Materials and Fuels Complex. Descriptions of the major components of the ER and the process in general have been provided elsewhere [2]. Salt and cadmium levels were measured, and multiple samples were obtained prior to performing the integrated test to establish an ER baseline for assessing the test results. The test consisted of four electrorefining batches of spent driver fuel with approximately 50 kg heavy metal. Typically, three to four ER runs are required to complete a batch. Fig. 1 shows pictures of the cathodes produced by three electrorefining runs during the second batch. The cathode No. 3 in the figure has clearly different morphology than that of the first two. The cathodes produced by the other three batches have the similar morphology as those pictured. The first and second cathodes are ordinary uranium dendrite, and the third and fourth cathode show typically high Zr content morphology [3]. The end-point for each batch was determined by weighing each anode basket and assuring a net residue mass being equal or less than 3.0 kg. The 3.0 kg residue included any un-dissolved fuel constituents and adhering salt. Previous operating experience has shown that uranium dissolution in excess of 99.7 wt% was achieved when using this established end-point. Cladding hull samples were taken from each basket after it was removed from the ER. The actinide dissolution efficiency will be evaluated when the analytical results become available. Cathode No. 1 Cathode No. 2 Cathode No. 3Fig. 1 Three cathodes produced through electrorefining the second batch of spent EBR-II driver fuelAs a part of the integrated efficiency test, the cat.
Book Synopsis Proceedings of the ... International Conference on Nuclear Engineering by :
Download or read book Proceedings of the ... International Conference on Nuclear Engineering written by and published by . This book was released on 2000 with total page 838 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis The EBR-II Spent Fuel Treatment Program by :
Download or read book The EBR-II Spent Fuel Treatment Program written by and published by . This book was released on 1995 with total page 9 pages. Available in PDF, EPUB and Kindle. Book excerpt: Argonne National Laboratory has refurbished and equipped an existing hot cell facility for demonstrating a high-temperature electrometallurgical process for treating spent nuclear fuel from the Experimental Breeder Reactor-11. Two waste forms will be produced and qualified for geologic disposal of the fission and activation products. Relatively pure uranium will be separated for storage. Following additional development, transuranium elements will be blended into one of the high-level waste streams. The spent fuel treatment program will help assess the viability of electrometallurgical technology as a spent fuel management option.
Book Synopsis Status and Trends in Spent Fuel Reprocessing by : International Atomic Energy Agency
Download or read book Status and Trends in Spent Fuel Reprocessing written by International Atomic Energy Agency and published by IAEA. This book was released on 2005 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt: The management of spent fuel arising from nuclear power production is a crucial issue for the sustainable development of nuclear energy. The IAEA has issued several publications in the past that provide technical information on the global status and trends in spent fuel reprocessing and associated topics, and one reason for this present publication is to provide an update of this information which has mostly focused on the conventional technology applied in the industry. However, the scope of this publication has been significantly expanded in an attempt to make it more comprehensive and by including a section on emerging technologies applicable to future innovative nuclear systems, as are being addressed in such international initiatives as INPRO, Gen IV and MICANET. In an effort to be informative, this publication attempts to provide a state-of-the-art review of these technologies, and to identify major issues associated with reprocessing as an option for spent fuel management. It does not, however, provide any detailed information on some of the related issues such as safety or safeguards, which are addressed in other relevant publications.
Book Synopsis Status and Trends in Pyroprocessing of Spent Nuclear Fuels by : International Atomic Energy Agency
Download or read book Status and Trends in Pyroprocessing of Spent Nuclear Fuels written by International Atomic Energy Agency and published by . This book was released on 2021-10-19 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: The importance of recycling the spent nuclear fuel through partitioning processes has been recognized worldwide for increasing and sustaining nuclear energy.
Book Synopsis State-of-the-art Report on the Progress of Nuclear Fuel Cycle Chemistry by :
Download or read book State-of-the-art Report on the Progress of Nuclear Fuel Cycle Chemistry written by and published by . This book was released on 2018 with total page 148 pages. Available in PDF, EPUB and Kindle. Book excerpt: The implementation of advanced nuclear systems requires that new technologies associated with the back end of the fuel cycle are developed. The separation of minor actinides from other fuel components is one of the advanced concepts being studied to help close the nuclear fuel cycle and to improve the long-term effects on the performance of geological repositories. Separating spent fuel elements and subsequently converting them through transmutation into short-lived nuclides should considerably reduce the longterm risks associated with nuclear power generation.
