Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Effects Of An Embedded Vortex On Injectant From A Single Film Cooling Hole In A Turbulent Boundary Layer
Download Effects Of An Embedded Vortex On Injectant From A Single Film Cooling Hole In A Turbulent Boundary Layer full books in PDF, epub, and Kindle. Read online Effects Of An Embedded Vortex On Injectant From A Single Film Cooling Hole In A Turbulent Boundary Layer ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Effects of an Embedded Vortex on Injectant from a Single Film-cooling Hole in a Turbulent Boundary Layer by : P. M. Ligrani
Download or read book Effects of an Embedded Vortex on Injectant from a Single Film-cooling Hole in a Turbulent Boundary Layer written by P. M. Ligrani and published by . This book was released on 1989 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Effects of embedded longitudinal vortices on heat transfer in turbulent boundary layers with injection from a single film-cooling hole are described. These results were obtained at a free-stream velocity of 10 m/s, with a film-cooling hole inclined 30 deg to the horizontal and a blowing ratio of about 0.50. The ratio of vortex core diameter to injection hole diameter was 1.58, and the ratio of circulation to injection velocity time hole diameter was about 3.16. Coolant distributions and spatially resolved heat transfer measurements indicate that injection hole centerlines must be at least 2.9–3.4 vortex core diameters away from the vortex center in the lateral direction to avoid significant alterations to wall heat transfer and distributions of film coolant. Under these circumstances, protection from film cooling is evident at least up to 55 hole diameters downstream of injection. When the injection hole is closer to the vortex center, secondary flows convect most injectant into the vortex upwash and thermal protection from film cooling is destroyed for streamwise locations from the injection hole greater than 17.5 hole diameters.
Book Synopsis Effect of Vortex Circulation on Injectant from a Single Film-cooling Hole and a Row of Film-cooling Holes in a Turbulent Boundary Layer by : Douglas William Craig
Download or read book Effect of Vortex Circulation on Injectant from a Single Film-cooling Hole and a Row of Film-cooling Holes in a Turbulent Boundary Layer written by Douglas William Craig and published by . This book was released on 1989 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Effects of an Embedded Vortex on a Single Film-cooling Jet in a Turbulent Boundary Layer by : Warren W. Williams
Download or read book Effects of an Embedded Vortex on a Single Film-cooling Jet in a Turbulent Boundary Layer written by Warren W. Williams and published by . This book was released on 1988 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Effects of embedded longitudinal vortices on heat transfer in a turbulent boundary layer film cooled from a single injections hole are discussed. Film coolant was injected at blowing ratios 0.50 to 1.50 at a freestream velocity of 10 m/s. A single longitudinal vortex was induced upstream of the film-cooling holes. Heat transfer measurement were made downstream of injection. Flow visualization tests were conducted after the injectant was contaminated with smoke. Surveys of mean velocity and mean temperature were also made in different spanwise normal planes. For all blowing ratios examined, the embedded vortices cause significant alterations to wall heat transfer and to film-cooling distributions. Embedded vortex, Film-cooling single jet, Heat transfer, Endwall secondary flows. (jes).
Book Synopsis Effect of Vortex Circulation on Injectant from a Single Film-Cooling Hole and a Row of Film-Cooling Holes in a Turbulent Boundary Layer. Part 2. Injection Beneath the Vortex Upwash by : Pisut Kaisuwan
Download or read book Effect of Vortex Circulation on Injectant from a Single Film-Cooling Hole and a Row of Film-Cooling Holes in a Turbulent Boundary Layer. Part 2. Injection Beneath the Vortex Upwash written by Pisut Kaisuwan and published by . This book was released on 1989 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results are presented which illustrate the effects of single embedded longitudinal vortices on heat transfer and injectant downstream of a row of film-cooling holes and downstream of a single hole in a turbulent boundary layer. Changes resulting as circulation magnitudes of the vortices are varied from 0.0 to 0.144 sq m/s. Mean temperature results are presented which show how the injectant is distorted and redistributed by vortices, along with heat transfer measurements and mean velocity surveys. Injection hole diameter is 0.952 cm to give a ratio of vortex core diameter to hole diameter of about 1.5-1.6. Freestream velocity is maintained at 10 m/s, and the blowing ratio is approximately 0.5. Film-cooling holes are oriented 30 deg with respect to the test surface. Stanton numbers are measured on a constant heat flux surface with a nondimensional temperature parameter of about 1.5. The situation studied is one where the middle injection hole is beneath the vortex upwash. For all results, vortex centers pass well within 2.9 vortex core diameters of the middle injection hole. To quantify influences of the vortices on the injectant, the parameter S is introduced, defined as the ratio of vortex circulation to injection hole diameter times mean injection velocity. The perturbation to film injectant and local heat transfer is determined by the magnitude of S. When S is> 1.0-1.5, injectant is swept into the vortex upwash and above the vortex core by secondary flows, and Stanton number data show little evidence of injectant beneath the vortex core and downwash near the wall. Theses. (edc).
Book Synopsis Effect of Vortex Circulation on Injectant from a Single Film-Cooling Hole and a Row of Film-Cooling Holes in a Turbulent Boundary Layer. Part 2. Injection Beneath the Vortex Upwash by :
Download or read book Effect of Vortex Circulation on Injectant from a Single Film-Cooling Hole and a Row of Film-Cooling Holes in a Turbulent Boundary Layer. Part 2. Injection Beneath the Vortex Upwash written by and published by . This book was released on 1989 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results are presented which illustrate the effects of single embedded longitudinal vortices on heat transfer and injectant downstream of a row of film-cooling holes and downstream of a single hole in a turbulent boundary layer. Changes resulting as circulation magnitudes of the vortices are varied from 0.0 to 0.144 sq m/s. Mean temperature results are presented which show how the injectant is distorted and redistributed by vortices, along with heat transfer measurements and mean velocity surveys. Injection hole diameter is 0.952 cm to give a ratio of vortex core diameter to hole diameter of about 1.5-1.6. Freestream velocity is maintained at 10 m/s, and the blowing ratio is approximately 0.5. Film-cooling holes are oriented 30 deg with respect to the test surface. Stanton numbers are measured on a constant heat flux surface with a nondimensional temperature parameter of about 1.5. The situation studied is one where the middle injection hole is beneath the vortex upwash. For all results, vortex centers pass well within 2.9 vortex core diameters of the middle injection hole. To quantify influences of the vortices on the injectant, the parameter S is introduced, defined as the ratio of vortex circulation to injection hole diameter times mean injection velocity. The perturbation to film injectant and local heat transfer is determined by the magnitude of S. When S is> 1.0-1.5, injectant is swept into the vortex upwash and above the vortex core by secondary flows, and Stanton number data show little evidence of injectant beneath the vortex core and downwash near the wall. Theses. (edc).
Book Synopsis Effects of Vortices with Different Circulations on Heat Transfer and Injectant Downstream of a Single Film-cooling Hole in a Turbulent Boundary Layer by : P. M. Ligrani
Download or read book Effects of Vortices with Different Circulations on Heat Transfer and Injectant Downstream of a Single Film-cooling Hole in a Turbulent Boundary Layer written by P. M. Ligrani and published by . This book was released on 1990 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Results are presented that illustrate the effects of single embedded longitudinal vortices on heat transfer and injectant downstream of a single film-cooling hole in a turbulent boundary layer. Attention is focused on the changes resulting as circulation magnitudes of the vortices are varied from 0.0 to 0.15 m2/s. Mean temperature results are presented that show how injectant is distorted and redistributed by vortices, along with heat transfer measurements and mean velocity surveys. Injection hole diameter is 0.952 cm to give a ratio of vortex core diameter to hole diameter of about 1.5-1.6. The free-stream velocity is maintained at 10 m/s, and the blowing ratio is approximately 0.5. The film-cooling hole is oriented 30 deg with respect to the test surface. Stanton numbers are measured on a constant heat flux surface with a nondimensional temperature parameter of about 1.5. Two different situations are studied: one where the injection hole is beneath the vortex downwash, and one where the injection hole is beneath the vortex upwash. For both cases, vortex centers pass well within 2.9 vortex core diameters of the centerline of the injection hole. To quantify the influences of the vortices on the injectant and local heat transfer, the parameter S is used, defined as the ratio of vortex circulation to injection hole diameter times mean injection velocity. When S is greater than 1.0-1.5, injectant is swept into the vortex upwash and above the vortex core by secondary flows, and Stanton number data show evidence of injectant beneath the vortex core and downwash near the wall for x/d only up to 33.6. For larger x/d, local Stanton numbers are augmented by the vortices by as much as 23 percent relative to film-cooled boundary layers with no vortices. When S is less than 1.0-1.5, some injectant remains near the wall beneath the vortex core and downwash where it continues to provide some thermal protection. In some cases, the protection provided by film cooling is augmented because of vortex secondary flows, which cause extra injectant to accumulate near vortex upwash regions.
Book Synopsis The Effects of an Embedded Vortex on a Film Cooled Turbulent Boundary Layer by : Stephen L. Joseph
Download or read book The Effects of an Embedded Vortex on a Film Cooled Turbulent Boundary Layer written by Stephen L. Joseph and published by . This book was released on 1986 with total page 222 pages. Available in PDF, EPUB and Kindle. Book excerpt: This thesis was designed to model some of the secondary flow effects on endwalls, blades, and combustion chambers of gas turbine engines. Measurements were made in a turbulent boundary layer developing over a flat plate, using a single row of injection holes spaced three diameters apart inclined at 30 degrees with respect to horizontal. The injection system was designed to provide uniform injection temperatures for various blowing rates with discharge coefficients ranging from 0.58 to 0.73. The heat transfer surface was designed to provide constant heat flux with adjustable temperature range. Experimental heat transfer results were obtained with a turbulent boundary layer only, with boundary layer and injection of film cooling, with boundary layer and embedded vortex, and finally with boundary layer, film cooling, and embedded vortex. The effects of the vortex on heat transfer in the film cooled boundary layer are significant and important: (1) On the downwash side of the vortex, heat transfer is augmented, effects of the film cooling are negated and local hot spots will exist in engines. (2) Near the upwash side of the vortex coolant is pushed to the side of the vortex, appearing to augment the protection provided by film cooling.
Book Synopsis Effect of Vortex Circulation on Injectant from a Single Film-cooling Hole and a Row of Film-cooling Holes in a Turbulent Boundary Layer by : Douglas William Craig
Download or read book Effect of Vortex Circulation on Injectant from a Single Film-cooling Hole and a Row of Film-cooling Holes in a Turbulent Boundary Layer written by Douglas William Craig and published by . This book was released on 1989 with total page 286 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Scientific and Technical Aerospace Reports by :
Download or read book Scientific and Technical Aerospace Reports written by and published by . This book was released on 1992 with total page 284 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Applied mechanics reviews written by and published by . This book was released on 1948 with total page 400 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ASME Technical Papers written by and published by . This book was released on 2000 with total page 574 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Turbulence Structure Resulting from Interaction Between an Embedded Vortex and Wall Jet by : James G. Green
Download or read book Turbulence Structure Resulting from Interaction Between an Embedded Vortex and Wall Jet written by James G. Green and published by . This book was released on 1989 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: Interactions of wall jets and vortices embedded in turbulent boundary layers commonly occur near gas turbine blades and endwalls where film cooling is employed. These interactions frequently result in undesirable heat transfer effects at blade and endwall surfaces. In this research, a crossed hot-wire probe is used to measure the turbulence structure resulting from this type of interaction. The vortex is generated using a half-delta-wing vortex generator mounted at 12 degrees with respect to a 10 m/s mean velocity flow over a flat plate. A single injection hole, .95 cm in diameter, inclined 30 degrees to the horizontal, is located under the vortex downwash, 58 cm downstream from the vortex generator. Baseline measurements were made at one streamwise location downstream of the injection hole for the cases: (1) boundary layer only; (2) boundary layer with vortex, and (3) boundary layer with wall jet. Measurement of the interaction between the boundary layer, vortex and 2.5 blowing ratio wall jet was also made at this location. The 1.5 blowing ratio wall jet interaction was measured at three additional streamwise locations. Reynolds stress tensor components, vorticity distributions and mean velocities show that the vortex significantly alters the turbulence structure of the 1.5 blowing ratio wall jet at all four streamwise locations. Here the injectant is swept away from the injection hole by the vortex rotation. The most significant alterations to the turbulence structure occur in the vortex upwash region and beneath the vortex core. The 2.5 blowing ratio jet is much more resistant to disturbance by the vortex. (kr).
Author :Advisory Committee on Technology and Society Publisher :National Academies Press ISBN 13 :9780309037860 Total Pages :1298 pages Book Rating :4.0/5 (378 download)
Book Synopsis Cities and Their Vital Systems by : Advisory Committee on Technology and Society
Download or read book Cities and Their Vital Systems written by Advisory Committee on Technology and Society and published by National Academies Press. This book was released on 1989 with total page 1298 pages. Available in PDF, EPUB and Kindle. Book excerpt: Cities and Their Vital Systems asks basic questions about the longevity, utility, and nature of urban infrastructures; analyzes how they grow, interact, and change; and asks how, when, and at what cost they should be replaced. Among the topics discussed are problems arising from increasing air travel and airport congestion; the adequacy of water supplies and waste treatment; the impact of new technologies on construction; urban real estate values; and the field of "telematics," the combination of computers and telecommunications that makes money machines and national newspapers possible.
Download or read book Rotating Machinery written by J. H. Kim and published by CRC Press. This book was released on 1992-05-01 with total page 766 pages. Available in PDF, EPUB and Kindle. Book excerpt: This work the first of two contains papers presented at an international conference on the technology of rotating machinery, which specifically address transport phenomena in terms of turbine cooling heat transfer, rotating surfaces, curved ducts and rotating channels, multiphase flow and more.
Download or read book Paper written by and published by . This book was released on 1999 with total page 542 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Engineering Turbulence Modelling and Experiments - 2 by : F. Martelli
Download or read book Engineering Turbulence Modelling and Experiments - 2 written by F. Martelli and published by Elsevier. This book was released on 2014-06-28 with total page 1012 pages. Available in PDF, EPUB and Kindle. Book excerpt: Today understanding turbulence is one of the key issues in tackling flow problems in engineering. Powerful computers and numerical methods are now available for solving flow equations, but the simulation of turbulence effects, which are nearly always important in practice, are still at an early stage of development. Successful simulation of turbulence requires the understanding of the complex physical phenomena involved and suitable models for describing the turbulence momentum, heat and mass transfer. The 89 papers, including 5 invited papers, in this volume present and discuss new developments in the area of turbulence modelling and measurements, with particular emphasis on engineering-related problems. The high standard of the contributions on the developing and testing of turbulent models attests to the world-wide interest this domain is currently attracting from researchers.
Download or read book Journal of Turbomachinery written by and published by . This book was released on 1991 with total page 758 pages. Available in PDF, EPUB and Kindle. Book excerpt:
