Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Development Of A Sorbent Based Technology For Control Of Mercury In Flue Gas
Download Development Of A Sorbent Based Technology For Control Of Mercury In Flue Gas full books in PDF, epub, and Kindle. Read online Development Of A Sorbent Based Technology For Control Of Mercury In Flue Gas ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Development of a Sorbent-based Technology for Control of Mercury in Flue Gas by :
Download or read book Development of a Sorbent-based Technology for Control of Mercury in Flue Gas written by and published by . This book was released on 1996 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper presents results of research being, conducted at Argonne National Laboratory on the capture of elemental mercury in simulated flue gases by using dry sorbents. Experimental results from investigation of various sorbents and chemical additives for mercury control are reported. Of the sorbents investigated thus far, an activited-carbon-based sorbent impregnated with about 15% (by weight) of sulfur compound provided the best results. The key parameters affecting mercury control efficiency in a fixed-bed reactor, such as reactor loading, reactor temperature, sorbent size distribution, etc., were also studied, and the results ire presented. In addition to activated-carbon-based sorbents, a non-carbon-based sorbent that uses an inactive substrate treated with active chemicals is being developed. Preliminary, experimental results for mercury removal by this newly developed sorbent are presented.
Book Synopsis Development of Mercury Control Technology for Coal-fired Systems by :
Download or read book Development of Mercury Control Technology for Coal-fired Systems written by and published by . This book was released on 1995 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt: The emission of hazardous air pollutants (air toxics) from various industrial processes has emerged as a major environmental issue that was singled out for particular attention in the Clean Air Act Amendments of 1990. In particular, mercury emissions are the subject of several current EPA studies because of concerns over possible serious effects on human health. Some of those emissions originate in the combustion of coal, which contains trace amounts of mercury, and are likely to be the subject of control requirements in the relatively near future. Data collected by the Department of Energy (DOE) and the Electric Power Research Institute (EPRI) at operating electric-power plants have shown that conventional flue-gas cleanup (FGC) technologies are not very effective in controlling emissions of mercury in general, and are particularly poor at controlling emissions of elemental mercury. This paper gives an overview of research being conducted at Argonne National Laboratory on improving the capture of mercury in flue gas through the use of dry sorbents and/or wet scrubbers. The results and conclusions to date from the Argonne research on dry sorbents can be summarized as follows: lime hydrates, either regular or high-surface-area, are not effective in removing elemental mercury; mercury removals are enhanced by the addition of activated carbon; mercury removals with activated carbon decrease with increasing temperature, larger particle size, and decreasing mercury concentration in the gas; chemical pretreatment (e.g., with sulfur or CaCl2) can greatly increase the removal capacity of activated carbon; chemically treated mineral substrates have the potential to be developed into effective and economical mercury sorbents; sorbents treated with different chemicals respond in significantly different ways to changes in flue-gas temperature.
Book Synopsis Ejército; revista ilustrada de las armas y servicios by :
Download or read book Ejército; revista ilustrada de las armas y servicios written by and published by . This book was released on 1961 with total page 118 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Investigation and Demonstration of Dry Carbon-Based Sorbent Injection for Mercury Control by : Terry Hunt
Download or read book Investigation and Demonstration of Dry Carbon-Based Sorbent Injection for Mercury Control written by Terry Hunt and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Public Service Company of Colorado and ADA Technologies, Inc. have performed a study of the injection of activated carbon for the removal of vapor-phase mercury from coal-fired flue gas streams. The project was completed under contract to the US Department of Energy's National Energy Technology Laboratory, with contributions from EPRI and Public Service Company. The prime contractor for the project was Public Service Company, with ADA Technologies as the major subcontractor providing technical support to all aspects of the project. The research and development effort was conducted in two phases. In Phase I a pilot facility was fabricated and tests were performed using dry carbon-based sorbent injection for mercury control on a coal-fired flue gas slipstream extracted from an operating power plant. Phase II was designed to move carbon injection technology towards commercial application on coal-fired power plants by addressing key reliability and operability concerns. Phase II field work included further development work with the Phase I pilot and mercury measurements on several of PSCo's coal-fired generating units. In addition, tests were run on collected sorbent plus fly ash to evaluate the impact of the activated carbon sorbent on the disposal of fly ash. An economic analysis was performed where pilot plant test data was used to develop a model to predict estimated costs of mercury removal from plants burning western coals. Testing in the pilot plant was undertaken to quantify the effects of plant configuration, flue gas temperature, and activated carbon injection rate on mercury removal. All three variables were found to significantly impact the mercury removal efficiency in the pilot. The trends were clear: mercury removal rates increased with decreasing flue gas temperature and with increasing carbon injection rates. Mercury removal was much more efficient with reverse-gas and pulse-jet baghouse configurations than with an ESP as the particulate control device. The native fly ash of the host unit provided significant mercury removal capacity, so that the activated carbon sorbent served as an incremental mercury removal mechanism. Tests run to characterize the waste product, a combination of fly ash and activated carbon on which mercury was present, showed that mercury and other RCRA metals of interest were all below Toxic Characteristic Leaching Procedure (TCLP) regulatory limits in the leachate. The presence of activated carbon in the fly ash was shown to have an effect on the use of fly ash as an additive in the manufacture of concrete, which could limit the salability of fly ash from a plant where activated carbon was used for mercury control.
Download or read book Lüdin Max (1919-?). written by and published by . This book was released on 1939 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Zeitungsausschnitte.
Book Synopsis Development of Mercury Control Enhancements for Flue-gas Cleanup Systems by :
Download or read book Development of Mercury Control Enhancements for Flue-gas Cleanup Systems written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Combustion sources, including those using coal for fuel, contribute a significant fraction of total anthropogenic mercury emissions. Unfortunately, recent field studies have shown that current flue-gas cleanup (FGC) systems are relatively ineffective in controlling elemental mercury, which is a major component of the mercury emissions for many systems. Research at Argonne National Laboratory has been focused on techniques to enhance the capture of elemental mercury in existing FGC systems. For dry processes, these studies have included evaluation of the factors that control mercury capture by commercial activated carbons (both with and without chemical pretreatment), testing of novel proprietary sorbents under development by several firms, and investigation of sorbents based upon chemical pretreatment of low-cost mineral substrates. To enhance the ability of wet scrubbers to capture mercury, the studies have looked at the effects of improved mass transfer through both mechanical and chemical means, as well as the conversion of elemental mercury into more soluble species that can be easily absorbed.
Book Synopsis Fundamental Understanding of Mercury Removal from Coal Combustion by : Erdem Sasmaz
Download or read book Fundamental Understanding of Mercury Removal from Coal Combustion written by Erdem Sasmaz and published by Stanford University. This book was released on 2011 with total page 195 pages. Available in PDF, EPUB and Kindle. Book excerpt: Coal-fired power plants are a major anthropogenic source of worldwide mercury (Hg) emissions. Since mercury is considered to be one of the most toxic metals found in the environment, Hg emissions from coal-fired power plants is of major environmental concern. Mercury in coal is vaporized into its gaseous elemental form throughout the coal combustion process. Elemental Hg can be oxidized in subsequent reactions with other gaseous components (homogeneous) and solid materials (heterogeneous) in coal-fired flue gases. While oxidized Hg in coal-fired flue gases is readily controlled by its adsorption onto fly ash and/or its dissolution into existing solution-based sulfur dioxide (SO2) scrubbers, elemental Hg is not controlled. The extent of elemental Hg formed during coal combustion is difficult to predict since it is dependent on the type of coal burned, combustion conditions, and existing control technologies installed. Therefore, it is important to understand heterogeneous Hg reaction mechanisms to predict the speciation of Hg emissions from coal-fired power plants to design and effectively determine the best applicable control technologies. In this work, theoretical and experimental investigations have been performed to investigate the adsorption and in some cases the oxidation, of Hg on solid surfaces, e.g., calcium oxide (CaO), noble metals and activated carbon (AC). The objective of this research is to identify potential materials that can be used as multi-pollutant sorbents in power plants by carrying out both high-level density functional theory (DFT) electronic structure calculations and experiments to understand heterogeneous chemical pathways of Hg. This research uses a fundamental science-based approach to understand the environmental problems caused by coal-fired energy production and provides solutions to the power generation industry for emissions reductions. Understanding the mechanism associated with Hg and SO2 adsorption on CaO will help to optimize the conditions or material to limit Hg emissions from the flue gas desulfurization process. Plane-wave DFT calculations were used to investigate the binding mechanism of Hg species and SO2 on the CaO(100) surface. The binding strengths on the high-symmetry CaO adsorption sites have been investigated for elemental Hg, SO2, mercury chlorides (HgCl and HgCl2) and mercuric oxide (HgO). It has been discovered that HgCl, HgCl2, and SO2 chemisorb on the CaO(100) surface at 0.125 ML coverage. Binding energies of elemental Hg are minimal indicating a physisorption mechanism. Noble metals such as palladium (Pd), gold (Au), silver (Ag), and copper (Cu) have been proposed to capture elemental Hg. Plane-wave DFT calculations have been carried out to investigate the mercury interactions with Pd binary alloys and overlays in addition to pure Pd, Au, Ag, and Cu surfaces. It has been determined that Pd has the highest mercury binding energy in comparison to other noble metals. In addition, Pd is found to be the primary surface atom responsible for increasing the adsorption of Hg with the surface in both Pd binary alloys and overlays. Deposition of Pd overlays on Au and Ag has been found to enhance the reactivity of the surface by shifting the d-states of surface atoms up in energy. The possible binding mechanisms of elemental Hg onto virgin, brominated and sulfonated AC fiber and brominated powder AC sorbents have been investigated through packed-bed experiments in a stream of air and simulated flue gas conditions, including SO2, hydrogen chloride (HCl), nitrogen oxide (NO) nitrogen dioxide (NO2). A combination of spectroscopy and plane-wave DFT calculations was used to characterize the sorption process. X-ray photoelectron spectroscopy (XPS) and x-ray absorption fine structure (XAFS) spectroscopy were used to analyze the surface and bulk chemical compositions of brominated AC sorbents reacted with Hg0. Through XPS surface characterization studies it was found that Hg adsorption is primarily associated with halogens on the surface. Elemental Hg is oxidized on AC surfaces and the oxidation state of adsorbed Hg is found to be Hg2+. Though plane-wave DFT and density of states (DOS) calculations indicate that Hg is more stable when it is bound to the edge carbon atom interacting with a single bromine bound atop of Hg, a model that includes an interaction between the Hg and an additional Br atom matches best with experimental data obtained from extended x-ray absorption fine structure (EXAFS) spectroscopy. The flue gas species such as HCl and bromine (Br2) enhance the Hg adsorption, while SO2 is found to decrease the Hg adsorption significantly by poisoning the active sites on the AC surface. The AC sorbents represent the most market-ready technology for Hg capture and therefore have been investigated by both theory and experiment in this work. Future work will include similar characterization and bench-scale experiments to test the metal-based materials for the sorbent and oxidation performance.
Book Synopsis Clean Air Act by : John B. Stephenson (au)
Download or read book Clean Air Act written by John B. Stephenson (au) and published by DIANE Publishing. This book was released on 2005-12 with total page 66 pages. Available in PDF, EPUB and Kindle. Book excerpt: In March 2005, the EPA issued a rule that will limit mercury emissions (ME) -- a toxic element that causes neurological problems -- from coal-fired power plants, the nation's largest ind'l. source of ME. Under the rule, ME are to be reduced from a baseline of 48 tons/yr. to 38 tons in 2010 & to 15 tons in 2018. The ME target for 2010 is based on the level of ME achievable with technol. for controlling other pollutants -- which also capture some mercury -- because it believed emerging mercury controls had not been adequately demonstrated. This report: describes the use, availability, & effectiveness of technol. to reduce ME at power plants; & identifies the factors that influence the cost of these technol. & reports on available cost estimates. Tables.
Book Synopsis Clean Air Act by : United States. Government Accountability Office
Download or read book Clean Air Act written by United States. Government Accountability Office and published by . This book was released on 2005 with total page 80 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Development and Evaluation of Low-cost Sorbents for Removal of Mercury Emissions from Coal Combustion Flue Gas by :
Download or read book Development and Evaluation of Low-cost Sorbents for Removal of Mercury Emissions from Coal Combustion Flue Gas written by and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: "Determining how physical and chemical properties of sorbents affect vapor-phase mercury adsorption has led to potential approached for tailoring the properties of sorbents for more effective mercury removal. ... Objectives: to determine how physical and chemical properties of sorbents affect mercury adsoprtion; to develop more cost-effective sorbents"--P. v.
Book Synopsis Control of mercury emissions from coalfired electric utility boilers interim report including errata dated 32102 by :
Download or read book Control of mercury emissions from coalfired electric utility boilers interim report including errata dated 32102 written by and published by DIANE Publishing. This book was released on with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Utilization of Partially Gasified Coal for Mercury Removal by :
Download or read book Utilization of Partially Gasified Coal for Mercury Removal written by and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In this project, General Electric Energy and Environmental Research Corporation (EER) developed a novel mercury (Hg) control technology in which the sorbent for gas-phase Hg removal is produced from coal in a gasification process in-situ at a coal burning plant. The main objective of this project was to obtain technical information necessary for moving the technology from pilot-scale testing to a full-scale demonstration. A pilot-scale gasifier was used to generate sorbents from both bituminous and subbituminous coals. Once the conditions for optimizing sorbent surface area were identified, sorbents with the highest surface area were tested in a pilot-scale combustion tunnel for their effectiveness in removing Hg from coal-based flue gas. It was determined that the highest surface area sorbents generated from the gasifier process ((almost equal to)600 m2/g) had about 70%-85% of the reactivity of activated carbon at the same injection rate (lb/ACF), but were effective in removing 70% mercury at injection rates about 50% higher than that of commercially available activated carbon. In addition, mercury removal rates of up to 95% were demonstrated at higher sorbent injection rates. Overall, the results of the pilot-scale tests achieved the program goals, which were to achieve at least 70% Hg removal from baseline emissions levels at 25% or less of the cost of activated carbon injection.
Book Synopsis Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas by :
Download or read book Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Sorbent injection technology represents one of the simplest and most mature approaches to controlling mercury emissions from coal-fired boilers. It involves injecting a solid material such as powdered activated carbon into the flue gas. The gas-phase mercury in the flue gas contacts the sorbent and attaches to its surface. The sorbent with the mercury attached is then collected by the existing particle control device along with the other solid material, primarily fly ash. During 2001, ADA Environmental Solutions (ADA-ES) conducted a full-scale demonstration of sorbent-based mercury control technology at the Alabama Power E.C. Gaston Station (Wilsonville, Alabama). This unit burns a low-sulfur bituminous coal and uses a hot-side electrostatic precipitator (ESP) in combination with a Compact Hybrid Particulate Collector (COHPAC{reg_sign}) baghouse to collect fly ash. The majority of the fly ash is collected in the ESP with the residual being collected in the COHPAC{reg_sign} baghouse. Activated carbon was injected between the ESP and COHPAC{reg_sign} units to collect the mercury. Short-term mercury removal levels in excess of 90% were achieved using the COHPAC{reg_sign} unit. The test also showed that activated carbon was effective in removing both forms of mercury-elemental and oxidized. However, a great deal of additional testing is required to further characterize the capabilities and limitations of this technology relative to use with baghouse systems such as COHPAC{reg_sign}. It is important to determine performance over an extended period of time to fully assess all operational parameters. The project described in this report focuses on fully demonstrating sorbent injection technology at a coal-fired power generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.
Book Synopsis Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas by : Sharon Sjostrom
Download or read book Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas written by Sharon Sjostrom and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Sorbent injection technology represents one of the simplest and most mature approaches to controlling mercury emissions from coal-fired boilers. It involves injecting a solid material such as powdered activated carbon into the flue gas. The gas-phase mercury in the flue gas contacts the sorbent and attaches to its surface. The sorbent with the mercury attached is then collected by the existing particle control device along with the other solid material, primarily fly ash. During 2001, ADA Environmental Solutions (ADA-ES) conducted a full-scale demonstration of sorbent-based mercury control technology at the Alabama Power E.C. Gaston Station (Wilsonville, Alabama). This unit burns a low-sulfur bituminous coal and uses a hot-side electrostatic precipitator (ESP) in combination with a Compact Hybrid Particulate Collector (COHPAC{reg_sign}) baghouse to collect fly ash. The majority of the fly ash is collected in the ESP with the residual being collected in the COHPAC{reg_sign} baghouse. Activated carbon was injected between the ESP and COHPAC{reg_sign} units to collect the mercury. Short-term mercury removal levels in excess of 90% were achieved using the COHPAC{reg_sign} unit. The test also showed that activated carbon was effective in removing both forms of mercury-elemental and oxidized. However, a great deal of additional testing is required to further characterize the capabilities and limitations of this technology relative to use with baghouse systems such as COHPAC{reg_sign}. It is important to determine performance over an extended period of time to fully assess all operational parameters. The project described in this report focuses on fully demonstrating sorbent injection technology at a coal-fired power generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.
Book Synopsis Development of New Sorbents to Remove Mercury and Selenium from Flue Gas. Final Report, September 1, 1993--August 31, 1994 by :
Download or read book Development of New Sorbents to Remove Mercury and Selenium from Flue Gas. Final Report, September 1, 1993--August 31, 1994 written by and published by . This book was released on 1995 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt: Mercury (Hg) and selenium (Se) are two of the volatile trace metals in coal, which are often not captured by conventional gas clean up devices of coal-fired boilers. An alternative is to use sorbents to capture the volatile components of trace metals after coal combustion. In this project sorbent screening tests were performed in which ten sorbents were selected to remove metallic mercury in N2. These sorbents included activated carbon, char prepared from Ohio No. 5 coal, molecular sieves, silica gel, aluminum oxide, hydrated lime, Wyoming bentonite, kaolin, and Amberite IR-120 (an ion-exchanger). The sorbents were selected based on published information and B & W's experience on mercury removal. The promising sorbent was then selected and modified for detailed studies of removal of mercury and selenium compounds. The sorbents were tested in a bench-scale adsorption facility. A known amount of each sorbent was loaded in the column as a packed bed. A carrier gas was bubbled through the mercury and selenium compounds. The vaporized species were carried by the gas and went through the sorbent beds. The amount of mercury and selenium compounds captured by the sorbents was determined by atomic absorption. Results are discussed.
Book Synopsis Developments of Sorbents for Mercury Removal From Flue Gas by : Evan J. Granite
Download or read book Developments of Sorbents for Mercury Removal From Flue Gas written by Evan J. Granite and published by . This book was released on 2000 with total page 2 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Development of Control Technology for Emissions of Mercury in Flue Gases by :
Download or read book Development of Control Technology for Emissions of Mercury in Flue Gases written by and published by . This book was released on 1995 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
