Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
A Heat Transfer Probe For Use In A High Temperature Gas
Download A Heat Transfer Probe For Use In A High Temperature Gas full books in PDF, epub, and Kindle. Read online A Heat Transfer Probe For Use In A High Temperature Gas ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis A Heat Transfer Probe for Use in a High Temperature Gas by : McGill University. Mechanical Engineering Research Laboratories
Download or read book A Heat Transfer Probe for Use in a High Temperature Gas written by McGill University. Mechanical Engineering Research Laboratories and published by . This book was released on 1963 with total page 212 pages. Available in PDF, EPUB and Kindle. Book excerpt: "This report deals with the analysis, design and construction of an instrument intended to measure gas temperature in excess of 2000°C. Preliminary experimental calibration of this instrument is compared with those two particular aspects of theoretical behaviour which have been dealt with. A platinum/platinum-rhodium thermocouple was used in calibration to a temperature of 1300°C. The instrument is a conductive-convective heat flux device. A fine stainless steel tube is heated by the hot gas and cooled internally by flowing water. The water is supplied by and returned respectively, through one of two copper tubes inside a water cooled stainless steel jacket. It is shown that with proper calibration and analysis the heat flux to the instrument is uniquely defined in terms of only two variables, the tube side pressure drop and the electrical resistance of the needle tube. The latter quantity can be made constant, however, and the heat flux is related solely to the instrument coolant flow pressure drop. The instrument can be calibrated versus other thermometric devices so that the outside film transfer coefficient and temperature can be deduced separately. A linear relationship and a high degree of sensitivity between instrument coolant pressure drop and the external gas temperature was discovered Rigorous analyses of tube side pressure drop of a one-dimensional fluid stream in cross-flow heat transfer and the electrical resistance of a thick walled annular conductor with three dimensional cross-flow temperature distribution are performed. Graphs of these quantities versus temperature are plotted for various conditions of heat transfer." --
Book Synopsis A Heat Flux Probe for Transient Measurements in High Temperature Gases by : Leroy Malvin Fingerson
Download or read book A Heat Flux Probe for Transient Measurements in High Temperature Gases written by Leroy Malvin Fingerson and published by . This book was released on 1962 with total page 362 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Heat Transfer in High-temperature Gas Flow by :
Download or read book Heat Transfer in High-temperature Gas Flow written by and published by . This book was released on 1982 with total page 240 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Total Temperature Probes for High-temperature Hypersonic Boundary-layer Measurements by : Cindy W. Albertson
Download or read book Total Temperature Probes for High-temperature Hypersonic Boundary-layer Measurements written by Cindy W. Albertson and published by . This book was released on 1993 with total page 40 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis A Cooled-tube Pyrometer with Experimental Results Obtained in a High-temperature Gas Stream by : George E. Glawe
Download or read book A Cooled-tube Pyrometer with Experimental Results Obtained in a High-temperature Gas Stream written by George E. Glawe and published by . This book was released on 1961 with total page 30 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Particle-to-gas Heat Transfer in Fluidized Beds by : A. C. Juveland
Download or read book Particle-to-gas Heat Transfer in Fluidized Beds written by A. C. Juveland and published by . This book was released on 1964 with total page 34 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis NASA Technical Note by : United States. National Aeronautics and Space Administration
Download or read book NASA Technical Note written by United States. National Aeronautics and Space Administration and published by . This book was released on 1959 with total page 430 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Measurements in Heat Transfer by : Ernst Rudolf Georg Eckert
Download or read book Measurements in Heat Transfer written by Ernst Rudolf Georg Eckert and published by Hemisphere Pub. This book was released on 1976 with total page 664 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book NBS Special Publication written by and published by . This book was released on 1918 with total page 1216 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Development of High-temperature Strain Gages by : J. W. Pitts
Download or read book Development of High-temperature Strain Gages written by J. W. Pitts and published by . This book was released on 1961 with total page 318 pages. Available in PDF, EPUB and Kindle. Book excerpt: A summary is presented of a research program aimed at the improvement of high-temperature strain gages of the electrical resistance type. Potential ceramic and metal components were evaluated and a gage was devised that was based on these evaluations. This gage (NBS 5B) was flexible and easy to install; however, it lacked resistance stability at higher temperatures. In an attempt to minimize this deficiency, ceramic cements were developed that showed greater electrical resistivity than had been previously observed in the range 800 to 1800 degrees Fahrenheit; also, a technique was devised for increasing the resistance to ground by applying a fired-on ceramic coating to the grid of a specifically developed unbacked gage. A study was made of the cause of the erratic response of cemented gages that had not been preheated prior to use. There were strong indications that the erratic response was caused mostly by the rapid decrease in resistance that accompanied structural changes in the cement.
Download or read book NBS Monograph written by and published by . This book was released on 1967 with total page 60 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Use of a Free Molecule Probe in High Speed Rarefied Gas Flow Studies by : Jaan Alfred Laurmann
Download or read book Use of a Free Molecule Probe in High Speed Rarefied Gas Flow Studies written by Jaan Alfred Laurmann and published by . This book was released on 1957 with total page 48 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Frontzeitung der NSDAP., Ortsgruppe Schmargendorf by :
Download or read book Frontzeitung der NSDAP., Ortsgruppe Schmargendorf written by and published by . This book was released on 1939 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Design, Fabrication, Calibration and Testing of High-temperature Sensors for Measurement of Surface Heat Flux, Temperature, and Total Heat Transfer by : Justin Alfred Myrick (Jr.)
Download or read book Design, Fabrication, Calibration and Testing of High-temperature Sensors for Measurement of Surface Heat Flux, Temperature, and Total Heat Transfer written by Justin Alfred Myrick (Jr.) and published by . This book was released on 2019 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: This dissertation outlines the design, fabrication, calibration and testing of sensors that can be used to measure surface heat flux, surface temperature and total surface heat transfer. These sensors, once calibrated, use in-depth thermocouple (TC) data to estimate the surface boundary conditions which allows operation at high temperatures and harsh thermal environments. Calibration of these sensors is accomplished through the one-probe, two-probe and total surface heat transfer calibration integral equation formulations. The one-probe calibration integral equation method (CIEM) can be used to predict the surface thermal boundary conditions of a field test using the in-depth TC temperature from that test and data from a calibration test which consists of measured surface boundary conditions and data from the same in-depth TC. The calibration integral equation has the form of a Volterra integral equation which is ill-posed and requires regularization to achieve a stable prediction. The one-probe calibration integral technique may only be used when the thermal boundary condition at the back surface of the sensor during the calibration and reconstruction tests is the same. The two-probe CIEM removes this restriction by requiring data from two calibration tests consisting of the measured surface thermal boundary conditions and corresponding temperature data from two in-depth TC probes. The two sets of calibration data are used to predict the surface thermal boundary conditions of a reconstruction test when the temperature data from the two in-depth TCs from the reconstruction test are provided. The calibration integral equation for determination of the total surface heat transfer uses a simplified two-dimensional geometry where three of the domain boundaries are adiabatic and the fourth is an unknown spatially variable surface heat flux. The total heat transfer into the domain is predicted using the average in-depth temperature data from a series of thermocouples located on a fixed plane parallel to the heated surface. These formulations had previously been tested using high temperature numerical data. However, it is essential to verify these methods using high temperature experimental data to demonstrate their use in physical applications. This dissertation also provided novel methods to estimate the necessary regularization parameters using the calibration data.
Download or read book Applied Mechanics Reviews written by and published by . This book was released on 1968 with total page 700 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Ludwig's Applied Process Design for Chemical and Petrochemical Plants by : A. Kayode Coker
Download or read book Ludwig's Applied Process Design for Chemical and Petrochemical Plants written by A. Kayode Coker and published by Gulf Professional Publishing. This book was released on 2014-11-29 with total page 1277 pages. Available in PDF, EPUB and Kindle. Book excerpt: The fourth edition of Ludwig’s Applied Process Design for Chemical and Petrochemical Plants, Volume Three is a core reference for chemical, plant, and process engineers and provides an unrivalled reference on methods, process fundamentals, and supporting design data.New to this edition are expanded chapters on heat transfer plus additional chapters focused on the design of shell and tube heat exchangers, double pipe heat exchangers and air coolers. Heat tracer requirements for pipelines and heat loss from insulated pipelines are covered in this new edition, along with batch heating and cooling of process fluids, process integration, and industrial reactors. The book also looks at the troubleshooting of process equipment and corrosion and metallurgy. Assists engineers in rapidly analyzing problems and finding effective design methods and mechanical specifications Definitive guide to the selection and design of various equipment types, including heat exchanger sizing and compressor sizing, with established design codes Batch heating and cooling of process fluids supported by Excel programs
Book Synopsis Precision Measurement and Calibration by : J. F. Swindells
Download or read book Precision Measurement and Calibration written by J. F. Swindells and published by . This book was released on 1968 with total page 534 pages. Available in PDF, EPUB and Kindle. Book excerpt:
