Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Swelling And Tensile Properties Of Neutron Irradiated Vanadium Alloys
Download Swelling And Tensile Properties Of Neutron Irradiated Vanadium Alloys full books in PDF, epub, and Kindle. Read online Swelling And Tensile Properties Of Neutron Irradiated Vanadium Alloys ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Swelling and Tensile Properties of Neutron-irradiated Vanadium Alloys by :
Download or read book Swelling and Tensile Properties of Neutron-irradiated Vanadium Alloys written by and published by . This book was released on 1990 with total page 15 pages. Available in PDF, EPUB and Kindle. Book excerpt: Vanadium-base alloys are candidates for use as structural material in magnetic fusion reactors. In comparison to other candidate structural materials (e.g., Type 316 stainless and HT-9 ferritic steels), vanadium-base alloys such as V-15Cr-5Ti and V-20Ti have intrinsically lower long-term neutron activation, neutron irradiation after-heat, biological hazard potential, and neutron-induced helium and hydrogen transmutation rates. Moreover, vanadium-base alloys can withstand a higher surface-heat, flux than steels because of their lower thermal stress factor. In addition to having these favorable neutronic and physical properties, a candidate alloy for use as structural material in a fusion reactor must have dimensional stability, i.e., swelling resistance, and resistance to embrittlement during the reactor lifetime at a level of structural strength commensurate with the reactor operating temperature and structural loads. In this paper, we present experimental results on the swelling and tensile properties of several vanadium-base alloys after irradiation at 420, 520, and 600°C to neutron fluences ranging from 0.3 to 1.9 x 1027 neutrons/m2 (17 to 114 atom displacements per atom (dpa)).
Book Synopsis Relationship of Microstructure and Tensile Properties for Neutron-Irradiated Vanadium Alloys by : BA. Loomis
Download or read book Relationship of Microstructure and Tensile Properties for Neutron-Irradiated Vanadium Alloys written by BA. Loomis and published by . This book was released on 1992 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt: The microstructures in V-15Cr-5Ti, V-10Cr-5Ti, V-3Ti-lSi, V-15Ti-7.5Cr, and V-20Ti alloys were examined by transmission electron microscopy after neutron irradiation at 600°C to 21 to 84 atom displacements per atom in the Materials Open Test Assembly of the Fast Flux Test Facility. The microstructures in these irradiated alloys were analyzed to determine the radiation-produced dislocation density, precipitate number density and size, and void number density and size. The results of these analyses were used to compute increases in yield stress and swelling of the irradiated alloys. The computed increase in yield stress was compared with the increase in yield stress determined from tension tests on these irradiated alloys. This comparison made it possible to evaluate the influence of alloy composition on the evolution of radiation-damaged microstructures and the resulting tensile properties.
Book Synopsis Relationship of Microstructure and Tensile Properties for Neutron-irradiated Vanadium Alloys by :
Download or read book Relationship of Microstructure and Tensile Properties for Neutron-irradiated Vanadium Alloys written by and published by . This book was released on 1990 with total page 28 pages. Available in PDF, EPUB and Kindle. Book excerpt: The microstructures in V-15Cr-5Ti, V-10Cr-5RTi, V-3Ti-1Si, V-15Ti-7.5Cr, and V-20Ti alloys were examined by transmission electron microscopy after neutron irradiation at 600°C to 21--84 atom displacements per atom in the Materials Open Test Assembly of the Fast Flux Test Facility. The microstructures in these irradiated alloys were analyzed to determine the radiation-produced dislocation density, precipitate number density and size, and void number density and size. The results of these analyses were used to compute increases in yield stress and swelling of the irradiated alloys. The computed increase in yield stress was compared with the increase in yield stress determined from tensile tests on these irradiated alloys. This comparison made it possible to evaluate the influence of alloy composition on the evolution of radiation-damaged microstructures and the resulting tensile properties. 11 refs.
Book Synopsis Effects of Fast-Neutron Irradiation on Tensile Properties and Swelling Behavior of Vanadium Alloys by : R. Carlander
Download or read book Effects of Fast-Neutron Irradiation on Tensile Properties and Swelling Behavior of Vanadium Alloys written by R. Carlander and published by . This book was released on 1973 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fast-neutron-induced void formation in commercial pure vanadium is dramatically reduced by additions of titanium and/or chromium. As little as 1 percent by weight titanium decreases the void number density and void volume fraction by factors of 30 and 100, respectively, compared with pure vanadium after exposure at 525 C (977 F) to a fluence of 1.1 x 1022 n/cm2, En > 0.1 MeV. Additions of 3 percent by weight titanium or greater suppress void formation entirely under the same exposure conditions. Alloys of 10 and 15 percent by weight chromium have also been found beneficial in limiting swelling. Internal-friction measurements show that the reduction in void formation in the vanadium-titanium alloys may be partly related to the removal of interstitial impurities, oxygen, and nitrogen by the titanium to form a coherent precipitate of Ti3O2 or a complex oxynitride. Excess oxygen in the alloy after consumption of the available titanium as a precipitate results in increased void formation and also loss of precipitate coherency.
Book Synopsis Correlation of Microstructure and Tensile and Swelling Behavior of Neutron-irradiated Vanadium Alloys by :
Download or read book Correlation of Microstructure and Tensile and Swelling Behavior of Neutron-irradiated Vanadium Alloys written by and published by . This book was released on 1991 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt: The microstructures of V-Ti, V-Cr-Ti, and V-Ti-Si alloys were characterized by transmission electron microscopy (TEM) after neutron irradiation in the Fast Flux Test Facility (FFTF) at 420 and 600°C to influences up to 114 dpa. Two types of irradiation-induced precipitates were identified, i.e., Ti2O and Ti5(Si, P)3. Blocky Ti(O, N, C) precipitates, which form by thermal processes during ingot fabrication, also were observed in all unirradiated and irradiated specimens. Irradiation-induced precipitation of spherical (
Book Synopsis The Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys by : DN. Braski
Download or read book The Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys written by DN. Braski and published by . This book was released on 1987 with total page 20 pages. Available in PDF, EPUB and Kindle. Book excerpt: Specimens of V-15Cr-5Ti, VANSTAR-7, and V-3Ti-1Si were encapsulated in molybdenum alloy tubes containing 7Li to prevent interstitial pickup and irradiated in the Fast Flux Test Facility (FFTF), using Materials Open Test Assembly (MOTA) experiments, to a damage level of 40 displacements per atom (dpa). The irradiation temperatures were 420, 520, and 600°C. For a better simulation of fusion reactor conditions, helium was preimplanted in some specimens using a modified version of the "tritium trick." The V-15Cr-5Ti alloy was most susceptible to irradiation hardening and helium embrittlement, followed by VANSTAR-7, and V-3Ti-1Si. VANSTAR-7 exhibited a relatively high maximum void swelling of ~6% at 520°C while V-15Cr-5Ti and V-3Ti-1Si had values of
Book Synopsis Properties of Reactor Structural Alloys After Neutron Or Particle Irradiation by : C. J. Baroch
Download or read book Properties of Reactor Structural Alloys After Neutron Or Particle Irradiation written by C. J. Baroch and published by ASTM International. This book was released on 1975 with total page 625 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Correlation of Microstructure and Tensile and Swelling Behavior of Neutron-irradiated Vanadium Alloys by :
Download or read book Correlation of Microstructure and Tensile and Swelling Behavior of Neutron-irradiated Vanadium Alloys written by and published by . This book was released on 1991 with total page 24 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Tensile Properties of Helium Injected and Neutron Irradiated Vanadium and Various Vanadium Alloys by : J.A. Dijkstra
Download or read book Tensile Properties of Helium Injected and Neutron Irradiated Vanadium and Various Vanadium Alloys written by J.A. Dijkstra and published by . This book was released on 1994 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Effects of Radiation on Substructure and Mechanical Properties of Metals and Alloys by :
Download or read book Effects of Radiation on Substructure and Mechanical Properties of Metals and Alloys written by and published by ASTM International. This book was released on 1973 with total page 546 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys by :
Download or read book Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys written by and published by . This book was released on 1986 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Specimens of V-15Cr-5Ti, VANSTAR-7, and V-3Ti-1Si were encapsulated in TZM tubes containing 7Li to prevent interstitial pickup and irradiated in FFTF (MOTA experiment) to a damage level of 40 dpa. The irradiation temperatures were 420, 520, and 600°C. For a better simulation of fusion reactor conditions, helium was preimplanted in some specimens using a modified version of the ''tritium trick.'' The V-15Cr-5Ti alloy was most susceptible to irradiation hardening and helium embrittlement, followed by VANSTAR-7 and V-3Ti-1Si. VANSTAR-7 exhibited a relatively high maximum void swelling of approx. 6% at 520°C while V-15Cr-5Ti and V-3Ti-1Si had values of less than 0.3% at all three temperatures. The V-3Ti-1Si clearly outperformed the other two vanadium alloys in resisting the effects of neutron irradiation.
Book Synopsis SWELLING OF NEUTRON-IRRADIATED VANADIUM ALLOYS. by : B.A. LOOMIS
Download or read book SWELLING OF NEUTRON-IRRADIATED VANADIUM ALLOYS. written by B.A. LOOMIS and published by . This book was released on 1989 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Tensile Properties of Helium Injected and Neutron Irradiated Vanadium and Various Vandium Alloys by : J. A. Dijkstra
Download or read book Tensile Properties of Helium Injected and Neutron Irradiated Vanadium and Various Vandium Alloys written by J. A. Dijkstra and published by . This book was released on 1994 with total page 16 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Vanadium Alloys for Structural Applications in Fusion Systems by :
Download or read book Vanadium Alloys for Structural Applications in Fusion Systems written by and published by . This book was released on 1991 with total page 21 pages. Available in PDF, EPUB and Kindle. Book excerpt: The current knowledge is reviewed on (1) the effects of neutron irradiation on tensile strength and ductility, ductile-brittle transition temperature, creep, fatigue, and swelling of vanadium-base alloys, (2) the compatibility of vanadium-base alloys with liquid lithium, water, and helium environments, and (3) the effects of hydrogen and helium on the physical and mechanical properties of vanadium alloys that are potential candidates for structural materials applications in fusion systems. Also, physical and mechanical properties issues are identified that have not been adequately investigated in order to qualify a vanadium-base alloy for the structural material in experimental fusion devices and/or in fusion reactors.
Book Synopsis The Post-Irradiation Tensile Properties and Microstructure of Several Vanadium Alloys by : DN. Braski
Download or read book The Post-Irradiation Tensile Properties and Microstructure of Several Vanadium Alloys written by DN. Braski and published by . This book was released on 1990 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: Tensile specimens of V-15Cr-5Ti, Vanstar-7, V-3Ti-lSi, and V-20TJ were irradiated at 420°C in FFTF-MOTA to a damage level of 82 dpa. Helium was preimplanted to levels up to 480 appm in selected specimens using a modified tritium trick. Irradiation hardeningwas the dominant effect influencing the post irradiation tensile properties, and it markedly increased the yield strength and reduced the total elongation. The V-15Cr-5Ti alloy was very sensitive to helium embrittlement, but Vanstar-7 and V-3Ti-lSi were only slightly affected. Without helium, negligible swelling was found in V-15Cr-5Ti and Vanstar-7, and only small values of swelling (
Book Synopsis The Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys. [Viewgraphs]. by :
Download or read book The Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys. [Viewgraphs]. written by and published by . This book was released on 1987 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper contains viewgraphs describing the effects of neutron irradiation on the tensile properties and microstructure of vanadium alloys in first wall fusion reactors. A tritium trick experiment was used to study the helium embrittlement and the stresses and strains on these materials in a controlled environment. (LSP).
Book Synopsis Effects of Radiation on Substructure and Mechanical Properties of Metals and Alloys by :
Download or read book Effects of Radiation on Substructure and Mechanical Properties of Metals and Alloys written by and published by . This book was released on 1973 with total page 600 pages. Available in PDF, EPUB and Kindle. Book excerpt:
![Download The Effect of Neutron Irradiation on the Tensile Properties and Microstructure of Several Vanadium Alloys. [Viewgraphs]. PDF Online Free](https://books.google.com/books/content/images/frontcover/5axEAQAACAAJ?fife=w200-h370)
