Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
High Field Solenoids For Muon Cooling
Download High Field Solenoids For Muon Cooling full books in PDF, epub, and Kindle. Read online High Field Solenoids For Muon Cooling ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis High Field Solenoids for Muon Cooling by :
Download or read book High Field Solenoids for Muon Cooling written by and published by . This book was released on 1999 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The proposed cooling system for the muon collider will consist of a 200 meter long line of alternating field straight solenoids interspersed with bent solenoids. The muons are cooled in all directions using a 400 mm long section liquid hydrogen at high field. The muons are accelerated in the forward direction by about 900 mm long, 805 MHz RF cavities in a gradient field that goes from 6 T to -6 T in about 300 mm. The high field section in the channel starts out at an induction of about 2 T in the hydrogen. As the muons proceed down the cooling channel, the induction in the liquid hydrogen section increases to inductions as high as 30 T. The diameter of the liquid hydrogen section starts at 750 mm when the induction is 2 T. As the induction in the cooling section goes up, the diameter of the liquid hydrogen section decreases. When the high field induction is 30 T, the diameter of the liquid hydrogen section is about 80 mm. When the high field solenoid induction is below 8.5 T or 9T, niobium titanium coils are proposed for generating .the magnetic field. Above 8.5 T or 9 T to about 20 T, graded niobium tin and niobium titanium coils would be used at temperatures down to 1.8 K. Above 20 T, a graded bybrid magnet system is proposed, where the high field magnet section (above 20 T) is either a conventional water cooled coil section or a water cooled Bitter type coil. Two types of superconducting coils have been studied. They include; epoxy impregnated intrinsically stable coils, and cable in conduit conductor (CICC) coils with helium in the conduit.
Book Synopsis HIGH FIELD SOLENOID FOR MUON COOLING. by : R. B. PALMER
Download or read book HIGH FIELD SOLENOID FOR MUON COOLING. written by R. B. PALMER and published by . This book was released on 2006 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: Magnets made with high-temperature superconducting (HTS) coils operating at low temperatures have the potential to produce extremely high fields for use in accelerators and beam lines. The specific application of interest that we are proposing is to use a very high field (of the order of 50 Tesla) solenoid to provide a very small beta region for the final stages of cooling for a muon collider. With the commercial availability of HTS conductor based on BSCCO technology with high current carrying capacity at 4.2 K, very high field solenoid magnets should be possible. In this paper we will evaluate the technical issues associated with building this magnet. In particular we address how to mitigate the high Lorentz stresses associated with this high field magnet.
Book Synopsis Study of High Field Superconducting Solenoids for Muon Beam Cooling by :
Download or read book Study of High Field Superconducting Solenoids for Muon Beam Cooling written by and published by . This book was released on 2007 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: The final beam cooling stages of a possible Muon Collider may require DC solenoid magnets with magnetic fields of 40-50 T in an aperture of 40-50 mm. In this paper we study possible solutions towards creating DC fields of that order using available superconductors. Several magnetic and mechanical designs, optimized for the maximum performance are presented and compared in terms of cost and size.
Book Synopsis SUPERCONDUCTING SOLENOIDS FOR THE MUON COLLIDER. by :
Download or read book SUPERCONDUCTING SOLENOIDS FOR THE MUON COLLIDER. written by and published by . This book was released on 2001 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The muon collider is a new idea for lepton colliders. The ultimate energy of an electron ring is limited by synchrotron radiation. Muons, which have a rest mass that is 200 times that of an electron can be stored at much higher energies before synchrotron radiation limits ring performance. The problem with muons is their short life time (2.1[micro]s at rest). In order to operate a muon storage ring large numbers of muon must be collected, cooled and accelerated before they decay to an electron and two neutrinos. As the authors see it now, high field superconducting solenoids are an integral part of a muon collider muon production and cooling systems. This report describes the design parameters for superconducting and hybrid solenoids that are used for pion production and collection, RF phase rotations of the pions as they decay into muons and the muon cooling (reduction of the muon emittance) before acceleration.
Book Synopsis Muon Collider Final Cooling in 30-50 T Solenoids by :
Download or read book Muon Collider Final Cooling in 30-50 T Solenoids written by and published by . This book was released on 2011 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Muon ionization cooling to the required normalized rms emittance of 25 microns transverse, and 72 mm longitudinal, can be achieved with liquid hydrogen in high field solenoids, provided that the momenta are low enough. At low momenta, the longitudinal emittance rises from the negative slope of energy loss versus energy. Assuming initial emittances that have been achieved in six dimensional cooling simulations, optimized designs are given using solenoid fields limited to 30, 40, and 50 T. The required final emittances are achieved for the two higher field cases. Preliminary simulations of transverse cooling in hydrogen, at low energies, suggests that muon collider emittance requirements can be met using solenoid fields of 40 T or more. It might also be acceptable with 30 T. But these simulations did not include hydrogen windows, matching or reacceleration, whose performance, with one exception, was based on numerical estimates. Full simulations of more stages are planned. The design and simulation of hydrogen windows must be included, and space charge effects, and absorber heating, calculated.
Book Synopsis AN IONIZATION COOLING CHANNEL FOR MUON BEAMS BASED ON ALTERNATING SOLENOIDS. by :
Download or read book AN IONIZATION COOLING CHANNEL FOR MUON BEAMS BASED ON ALTERNATING SOLENOIDS. written by and published by . This book was released on 1999 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: The muon collider requires intense, cooled muon bunches to reach the required luminosity. Due to the limited life-time of the muon, the cooling process must take place very rapidly. Ionization cooling seems to be our only option, given the large emittances of the muon beam from pion decay. However, this ionization cooling method has been found quite difficult to implement in practice. We describe a scheme based on the use of liquid hydrogen absorbers followed by r.f. cavities (''pillbox'' or ''open iris'' type), embedded in a transport lattice based on high field solenoids. These solenoidal fields are reversed periodically in order to suppress the growth of the canonical angular momentum. This channel has been simulated in detail with independent codes, featuring conventional tracking in e.m. fields and detailed simulation of multiple scattering and straggling in the absorbers and windows. These calculations show that the 15 Tesla lattice cools in 6-D phase space by a factor (almost equal to) 2 over a distance of 20 m.
Book Synopsis Bent Superconducting Solenoids for the Muon Cooling Experiment by :
Download or read book Bent Superconducting Solenoids for the Muon Cooling Experiment written by and published by . This book was released on 1999 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This report describes some solenoid design work done for the cooling experiment for the muon collider collaboration. This report describes an analysis section of superconducting solenoids that have a center line induction of 3.0 T. The section is bent in the shape of an S. Each bend in the S bends the muon beam one radian (57.3 degrees). The warm bore diameter of the solenoid bent solenoid is 300 to 320 mm. The radius of the bend at the solenoid center line is 1000 mm. This report shows the results of three dimensional field calculations and presents a solenoid design that will include four TPC detectors that are 240 mm in diameter and 550 mm long as well as a 1300 mm long section of 1300 MHz RF cavities. The TPC sections need a solenoid wann bore diameter of about 300 320 mm while RF cavities require a warm bore diameter of 440 mm. The superconducting solenoid design must take into account the varying warm bore diameter requirements for the magnet string yet meet the stringent solenoidal field uniformity requirements within the active volume of the four TPCs.
Book Synopsis Superconducting Solenoids for Muon-cooling in the Neutrino Factory by :
Download or read book Superconducting Solenoids for Muon-cooling in the Neutrino Factory written by and published by . This book was released on 2001 with total page 12 pages. Available in PDF, EPUB and Kindle. Book excerpt: The cooling channel for a neutrino factory consists of a series of alternating field solenoidal cells. The first section of the bunching cooling channel consists of 41 cells that are 2.75-m long. The second section of the cooling channel consists of 44 cells that are 1.65-m long. Each cell consists of a single large solenoid with an average diameter of 1.5 m and a pair of flux reversal solenoids that have an average diameter of 0.7 to 0.9 meters. The magnetic induction on axis reaches a peak value of about 5 T at the end of the second section of the cooling channel. The peak on axis field gradients in flux reversal section approaches 33 T/m. This report describes the two types of superconducting solenoid magnet sections for the muon-cooling channel of the proposed neutrino factory.
Book Synopsis High Field - Low Energy Muon Ionization Cooling Channel by :
Download or read book High Field - Low Energy Muon Ionization Cooling Channel written by and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Muon beams are generated with large transverse and longitudinal emittances. In order to achieve the low emittances required by a muon collider, within the short lifetime of the muons, ionization cooling is required. Cooling schemes have been developed to reduce the muon beam 6D emittances to ≈ 300 [mu]m-rad in transverse and ≈ 1-1.5 mm in longitudinal dimensions. The transverse emittance has to be further reduced to ≈ 50-25 [mu]m-rad with an upper limit on the longitudinal emittance of ≈ 76 mm in order to meet the high-energy muon collider luminosity requirements. Earlier studies of the transverse cooling of low energy muon beams in high field magnets showed a promising performance, but did not include transverse or longitudinal matching between the stages. In this study we present the first complete design of the high field-low energy ionization cooling channel with transverse and longitudinal matching. The channel design was based on strong focusing solenoids with fields of 25-30 T and low momentum muon beam starting at 135 MeV/c and gradually decreasing. The cooling channel design presented here is the first to reach ≈ 50 micron scale emittance beam. As a result, we present the channel's optimized design parameters including the focusing solenoid fields, absorber parameters and the transverse and longitudinal matching.
Book Synopsis Modeling the High-field Section of a Muon Helical Cooling Channel by :
Download or read book Modeling the High-field Section of a Muon Helical Cooling Channel written by and published by . This book was released on 2010 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: This paper describes the conceptual design and parameters of a short model of a high-field helical solenoid for muon beam cooling. Structural materials choices, fabrication techniques and first test results are discussed.
Book Synopsis Circularly Inclined Solenoid Channel for 6D Ionization Cooling of Muons by :
Download or read book Circularly Inclined Solenoid Channel for 6D Ionization Cooling of Muons written by and published by . This book was released on 2009 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ionization cooling is essential for realization of Muon Collider, muons beam based neutrino factories and other experiments involving muons. The simplest structure - absorber(s) immersed in alternating solenoidal magnetic field - provides only transverse cooling since the longitudinal motion in the most suitable momentum range (2-300MeV/c) is naturally anti-damped. To overcome this difficulty it is proposed to periodically tilt solenoids so that a rotating transverse magnetic field was created. By choosing the phase advance per period above a multiple of 2[pi] it is possible to ensure that muons with higher momentum make a longer path in the absorber (whether distributed or localized) thus providing longitudinal damping. Basic theory of such channel and results of tracking simulations are presented.
Book Synopsis Bent Solenoid Simulations for the Muon Cooling Experiment by :
Download or read book Bent Solenoid Simulations for the Muon Cooling Experiment written by and published by . This book was released on 1999 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The muon collider captures pions using solenoidal fields. The pion are converted to muons as they are bunched in an RF phase rotation system. Solenoids are used to focus the muons as their emitance is reduced during cooling. Bent solenoids are used to sort muons by momentum. This report describes a bent solenoid system that is part of a proposed muon cooling experiment. The superconducting solenoid described in this report consists of a straight solenoid that is 1.8 m long, a bent solenoid that is 1.0 m to 1.3 m long and a second straight solenoid that is 2.6 m long. The bent solenoid bends the muons over an angle of 57.3 degrees (1 radian). The bent solenoid has a minor coil radius (to the center of the coil) that is 0.24 m and a major radius (of the solenoid axis) of 1.0 m. The central induction along the axis is 3.0 T There is a dipole that generates an induction of 0.51 T, perpendicular to the plane of the bend, when the induction on the bent solenoid axis is 3.0 T.
Book Synopsis Investigation and Simulation of Muon Cooling Rings with Tilted Solenoids by :
Download or read book Investigation and Simulation of Muon Cooling Rings with Tilted Solenoids written by and published by . This book was released on 2003 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Alternating solenoid focused muon cooling ring without special bending magnets is considered and investigate in detail. Both fringe field between solenoid coils with opposite directed current, and an inclination of the coils in vertical plane are used to provide a bending and closing of the particle trajectories. Realistic (Maxwellian) magnetic field is calculated and used for a simulation. Methodic is developed and applied to find closed orbit at any energy, dispersion, region of stability, and other conventional accelerator characteristics. Earlier proposed RFOFO cooling ring with 200 MHz RF system and liquid hydrogen absorbers is investigated in detail. After an optimization, normalized 6D emittance about 20 mm3 and transmission 57% are obtained.
Book Synopsis High Field {u2013} Low Energy Muon Ionization Cooling Channel by :
Download or read book High Field {u2013} Low Energy Muon Ionization Cooling Channel written by and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Muon beams are generated with large transverse and longitudinal emittances. In order to achieve the low emittances required by a muon collider, within the short lifetime of the muons, ionization cooling is required. Cooling schemes have been developed to reduce the muon beam 6D emittances to ≈ 300 ?m–rad in transverse and ≈ 1–1.5 mm in longitudinal dimensions. The transverse emittance has to be further reduced to ≈ 50–25 ?m–rad with an upper limit on the longitudinal emittance of ≈ 76 mm in order to meet the high-energy muon collider luminosity requirements. Earlier studies of the transverse cooling of low energy muon beams in high field magnets showed a promising performance, but did not include transverse or longitudinal matching between the stages. In this study we present the first complete design of the high field-low energy ionization cooling channel with transverse and longitudinal matching. The channel design was based on strong focusing solenoids with fields of 25–30 T and low momentum muon beam starting at 135 MeV/c and gradually decreasing. The cooling channel design presented here is the first to reach ≈ 50 micron scale emittance beam. As a result, we present the channel’s optimized design parameters including the focusing solenoid fields, absorber parameters and the transverse and longitudinal matching.
Book Synopsis Some Options for the Muon Collider Capture and Decay Solenoids by :
Download or read book Some Options for the Muon Collider Capture and Decay Solenoids written by and published by . This book was released on 1995 with total page 8 pages. Available in PDF, EPUB and Kindle. Book excerpt: This report discusses some of the problems associated with using solenoid magnets to capture the secondary particles that are created when an intense beam of 8 to 10 GeV protons interacts with the target at the center of the capture region. Hybrid capture solenoids with inductions of 28 T and a 22T are described. The first 14 to 15 T of the solenoid induction will be generated by a superconducting magnet. The remainder of the field will be generated by a Bitter type of water cooled solenoid. The capture solenoids include a transition section from the high field solenoid to a 7 T decay channel where pions and kaons that come off of the target decay into muons. A short 7 T solenoidal decay channel between the capture solenoid system and the phase rotation system is described. A concept for separation of negative and positive pions and kaons is briefly discussed.
Book Synopsis Alternative Methods for Field Corrections in Helical Solenoids by :
Download or read book Alternative Methods for Field Corrections in Helical Solenoids written by and published by . This book was released on 2015 with total page 3 pages. Available in PDF, EPUB and Kindle. Book excerpt: Helical cooling channels have been proposed for highly efficient 6D muon cooling. Helical solenoids produce solenoidal, helical dipole, and helical gradient field components. Previous studies explored the geometric tunability limits on these main field components. In this paper we present two alternative correction schemes, tilting the solenoids and the addition of helical lines, to reduce the required strength of the anti-solenoid and add an additional tuning knob.
Book Synopsis High Field HTS Solenoid for a Muon Collider - Demonstrations, Challenges and Strategies by :
Download or read book High Field HTS Solenoid for a Muon Collider - Demonstrations, Challenges and Strategies written by and published by . This book was released on 2013 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
