Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Development And Evaluation Of Low Cost Sorbents For Removal Of Mercury Emissions From Coal Combustion Flue Gas
Download Development And Evaluation Of Low Cost Sorbents For Removal Of Mercury Emissions From Coal Combustion Flue Gas full books in PDF, epub, and Kindle. Read online Development And Evaluation Of Low Cost Sorbents For Removal Of Mercury Emissions From Coal Combustion Flue Gas ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Development and Evaluation of Low-cost Sorbents for Removal of Mercury Emissions from Coal Combustion Flue Gas by :
Download or read book Development and Evaluation of Low-cost Sorbents for Removal of Mercury Emissions from Coal Combustion Flue Gas written by and published by . This book was released on 1998 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: "Determining how physical and chemical properties of sorbents affect vapor-phase mercury adsorption has led to potential approached for tailoring the properties of sorbents for more effective mercury removal. ... Objectives: to determine how physical and chemical properties of sorbents affect mercury adsoprtion; to develop more cost-effective sorbents"--P. v.
Book Synopsis Control of mercury emissions from coalfired electric utility boilers interim report including errata dated 32102 by :
Download or read book Control of mercury emissions from coalfired electric utility boilers interim report including errata dated 32102 written by and published by DIANE Publishing. This book was released on with total page 346 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Development of Novel Activated Carbon-Based Adsorbents for Control of Mercury Emission From Coal-Fired Power Plants by :
Download or read book Development of Novel Activated Carbon-Based Adsorbents for Control of Mercury Emission From Coal-Fired Power Plants written by and published by . This book was released on 1997 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: The overall objective of this study is to evaluate pertinent design and operational parameters that would enable successful application of activated carbon adsorption for the reduction of mercury emissions from coal-fired power plants. The study will evaluate the most suitable impregnate such as sulfur, chloride and other chelating agents for its ability to enhance the adsorptive capacity of activated carbon for mercury vapor under various process conditions. The main process variables to be evaluated include temperature, mercury concentration and speciation, relative humidity, oxygen content, and presence of SO2 and NOx in the flue gas. The optimal amount of impregnate for each of these carbons will be determined based on the exhibited performance. Another important parameter which governs the applicability of adsorption technology for the flue gas clean up is the rate at which vapor phase mercury is being removed from the flue gas by activated carbon. Therefore, the second part of this study will evaluate the adsorption kinetics using the impregnated activated carbons listed above. The rate of mercury uptake will also be evaluated under the process conditions that are representative of coal-fired power plants. Concerned with the ability of the adsorbed mercury to migrate back into the environment once saturated adsorbent is removed from the system, the study will also focus on the mercury desorption rate as a function of the type of impregnate, loading conditions, and the time of contact prior to disposal.
Book Synopsis Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas by : Carl Richardson
Download or read book Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas written by Carl Richardson and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This project Final Report is submitted to the U.S. Department of Energy (DOE) as part of Cooperative Agreement DE-FC26-03NT41987, 'Sorbent Injection for Small ESP Mercury Control in Low Sulfur Eastern Bituminous Coal Flue Gas.' Sorbent injection technology is targeted as the primary mercury control process on plants burning low/medium sulfur bituminous coals equipped with ESP and ESP/FGD systems. About 70% of the ESPs used in the utility industry have SCAs less than 300 ft2/1000 acfm. Prior to this test program, previous sorbent injection tests had focused on large-SCA ESPs. This DOE-NETL program was designed to generate data to evaluate the performance and economic feasibility of sorbent injection for mercury control at power plants that fire bituminous coal and are configured with small-sized electrostatic precipitators and/or an ESP-flue gas desulfurization (FGD) configuration. EPRI and Southern Company were co-funders for the test program. Southern Company and Reliant Energy provided host sites for testing and technical input to the project. URS Group was the prime contractor to NETL. ADA-ES and Apogee Scientific Inc. were sub-contractors to URS and was responsible for all aspects of the sorbent injection systems design, installation and operation at the different host sites. Full-scale sorbent injection for mercury control was evaluated at three sites: Georgia Power's Plant Yates Units 1 and 2 [Georgia Power is a subsidiary of the Southern Company] and Reliant Energy's Shawville Unit 3. Georgia Power's Plant Yates Unit 1 has an existing small-SCA cold-side ESP followed by a Chiyoda CT-121 wet scrubber. Yates Unit 2 is also equipped with a small-SCA ESP and a dual flue gas conditioning system. Unit 2 has no SO2 control system. Shawville Unit 3 is equipped with two small-SCA cold-side ESPs operated in series. All ESP systems tested in this program had SCAs less than 250 ft2/1000 acfm. Short-term parametric tests were conducted on Yates Units 1 and 2 to evaluate the performance of low-cost activated carbon sorbents for removing mercury. In addition, the effects of the dual flue gas conditioning system on mercury removal performance were evaluated as part of short-term parametric tests on Unit 2. Based on the parametric test results, a single sorbent (e.g., RWE Super HOK) was selected for a 30-day continuous injection test on Unit 1 to observe long-term performance of the sorbent as well as its effects on ESP and FGD system operations as well as combustion byproduct properties. A series of parametric tests were also performed on Shawville Unit 3 over a three-week period in which several activated carbon sorbents were injected into the flue gas duct just upstream of either of the two Unit 3 ESP units. Three different sorbents were evaluated in the parametric test program for the combined ESP 1/ESP 2 system in which sorbents were injected upstream of ESP 1: RWE Super HOK, Norit's DARCO Hg, and a 62:38 wt% hydrated lime/DARCO Hg premixed reagent. Five different sorbents were evaluated for the ESP 2 system in which activated carbons were injected upstream of ESP 2: RWE Super HOK and coarse-ground HOK, Norit's DARCO Hg and DARCO Hg-LH, and DARCO Hg with lime injection upstream of ESP 1. The hydrated lime tests were conducted to reduce SO3 levels in an attempt to enhance the mercury removal performance of the activated carbon sorbents. The Plant Yates and Shawville studies provided data required for assessing carbon performance and long-term operational impacts for flue gas mercury control across small-sized ESPs, as well as for estimating the costs of full-scale sorbent injection processes.
Book Synopsis Development of a Novel Activated Carbon Based Adsorbents for Control of Mercury Emissions from Coal-Fired Power Plants by :
Download or read book Development of a Novel Activated Carbon Based Adsorbents for Control of Mercury Emissions from Coal-Fired Power Plants written by and published by . This book was released on 1997 with total page 18 pages. Available in PDF, EPUB and Kindle. Book excerpt: The overall objective of this study is to evaluate pertinent design and operational parameters that would enable successful application of activated carbon adsorption for the reduction of mercury emissions from coal-fired power plants. The study will evaluate the most suitable impregnate such as sulfur, chloride and other chelating agents for its ability to enhance the adsorptive capacity of activated carbon for mercury vapor under various process conditions. The main process variables to be evaluated include temperature, mercury concentration and speciation, relative humidity, oxygen content, and presence of S02 and NO(subscript x) in the flue gas. The optimal amount of impregnate for each of these carbons will be determined based on the exhibited performance. Another important parameter which governs the applicability of adsorption technology for the flue gas clean up is the rate at which vapor phase mercury is being removed from the flue gas by activated carbon. Therefore, the second part of this study will evaluate the adsorption kinetics using the impregnated activated carbons listed above. The rate of mercury uptake will also be evaluated under the process conditions that are representative of coal-fired power plants. Concerned with the ability of the adsorbed mercury to migrate back into the environment once saturated adsorbent is removed from the system, the study will also focus on the mercury desorption rate as a function of the type of impregnate, loading conditions, and the time of contact prior to disposal.
Author :United States. Congress. Senate. Committee on Environment and Public Works. Subcommittee on Clean Air, Climate Change, and Nuclear Safety Publisher :Amicus ISBN 13 : Total Pages :216 pages Book Rating :4.0/5 ( download)
Book Synopsis Implementation of the New Air Quality Standards for Particulate Matter and Ozone by : United States. Congress. Senate. Committee on Environment and Public Works. Subcommittee on Clean Air, Climate Change, and Nuclear Safety
Download or read book Implementation of the New Air Quality Standards for Particulate Matter and Ozone written by United States. Congress. Senate. Committee on Environment and Public Works. Subcommittee on Clean Air, Climate Change, and Nuclear Safety and published by Amicus. This book was released on 2005 with total page 216 pages. Available in PDF, EPUB and Kindle. Book excerpt: Amicus Readers at level 1 include: a picture glossary, a table of contents, index, websites, and literacy notes located in the back of each book. Additionally, content words are introduced within the text supported by a variety of photo labels. In particular, this title describes different ways that birthdays are celebrated. Includes simple craft.
Book Synopsis Preparation and Evaluation of Sulfur Containing Adsorbents for Removal of Mercury from Simulated Coal Combustion of Flue Gases by : Hsing-Cheng Hsi
Download or read book Preparation and Evaluation of Sulfur Containing Adsorbents for Removal of Mercury from Simulated Coal Combustion of Flue Gases written by Hsing-Cheng Hsi and published by . This book was released on 2001 with total page 374 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Evaluating sorbents produced from waste to remove mercury in simulated flue gases from coal combustion by : Hemantha Revata Seneviratne
Download or read book Evaluating sorbents produced from waste to remove mercury in simulated flue gases from coal combustion written by Hemantha Revata Seneviratne and published by . This book was released on 2008 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Evaluation of Sorbents for the Cleanup of Coal-derived Synthesis Gas at Elevated Temperatures by : David Joseph Couling
Download or read book Evaluation of Sorbents for the Cleanup of Coal-derived Synthesis Gas at Elevated Temperatures written by David Joseph Couling and published by . This book was released on 2012 with total page 182 pages. Available in PDF, EPUB and Kindle. Book excerpt: Integrated Gasification Combined Cycle (IGCC) with carbon dioxide capture is a promising technology to produce electricity from coal at a higher efficiency than with traditional subcritical pulverized coal (PC) power plants. As with any coal-based technology, however, it is of critical importance to develop efficient techniques to reduce the emissions of its many environmental pollutants, including not only carbon dioxide, but also sulfur and trace metals such as lead or mercury. One potential method to improve the efficiency for IGCC is through the use of solid sorbents that operate at elevated temperatures. Because many of these technologies are in their infancy and have yet to be commercially demonstrated, a strong desire exists to develop methods to critically evaluate these technologies more rapidly and inexpensively than can be done through experiments alone. In this thesis we applied computational techniques to investigate the feasibility of sorbents for the warm temperature removal of two key pollutants, carbon dioxide and mercury. We developed pressure swing adsorption models for the removal of carbon dioxide using both metal oxide and metal hydroxide sorbents and incorporated them into IGCC process simulations in Aspen Plus in order to evaluate the energy penalties associated with using these carbon dioxide capture technologies. We identified the optimal properties of CO2 sorbents for this application. Although warm CO2 capture using solid sorbents could lead to slight efficiency increases over conventional cold cleanup methods, the potential gains are much smaller than previously estimated. In addition, we used density functional theory to screen binary metal alloys, metal oxides, and metal sulfides as potential sorbents for mercury capture. We computed the thermochemistry of 40 different potential mercury sorbents to evaluate their affinity for mercury at the low concentrations and elevated temperatures found in the coal gas stream. We also evaluated the tendency of these sorbent materials to react with major components of the gas stream, such as hydrogen or steam. Finally, we tested the mercury adsorption characteristics of three of the most promising materials experimentally. Our experimental observations showed good qualitative agreement with our density functional theory calculations.
Book Synopsis ASSESSMENT OF LOW COST NOVEL SORBENTS FOR COAL-FIRED POWER PLANT MERCURY CONTROL. by :
Download or read book ASSESSMENT OF LOW COST NOVEL SORBENTS FOR COAL-FIRED POWER PLANT MERCURY CONTROL. written by and published by . This book was released on 2004 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: This is a Technical Report under a program funded by the Department of Energy's National Energy Technology Laboratory (NETL) to obtain the necessary information to assess the viability of lower cost alternatives to commercially available activated carbon for mercury control in coal-fired utilities. During this reporting period, several sorbent samples have been tested by URS in their laboratory fixed-bed system. The sorbents were evaluated under conditions simulating flue gas from power plants burning Powder River Basin (PRB) and low sulfur eastern bituminous coals. The equilibrium adsorption capacities of the sorbents for both elemental and oxidized mercury are presented. A team meeting discussing the overall program and meetings with Midwest Generation and Wisconsin Electric Power Company (WEPCO) concerning field testing occurred during this reporting period.
Book Synopsis Development and Evaluation of Nanoscale Sorbents for Mercury Capture from Warm Fuel Gas by :
Download or read book Development and Evaluation of Nanoscale Sorbents for Mercury Capture from Warm Fuel Gas written by and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Advanced Gasification By-Product Utilization by : M. Mercedes Maroto-Valer
Download or read book Advanced Gasification By-Product Utilization written by M. Mercedes Maroto-Valer and published by . This book was released on 2006 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: With the recent passing of new legislation designed to permanently cap and reduce mercury emissions from coal-fired utilities, it is more important than ever to develop and improve upon methods of controlling mercury emissions. One promising technique is carbon sorbent injection into the flue gas of the coal-fired power plant. Currently, this technology is very expensive as costly commercially activated carbons are used as sorbents. There is also a significant lack of understanding of the interaction between mercury vapor and the carbon sorbent, which adds to the difficulty of predicting the amount of sorbent needed for specific plant configurations. Due to its inherent porosity and adsorption properties as well as on-site availability, carbons derived from gasifiers are potential mercury sorbent candidates. Furthermore, because of the increasing restricted use of landfilling, the coal industry is very interested in finding uses for these materials as an alternative to the current disposal practice. The results of laboratory investigations and supporting technical assessments conducted under DOE Subcontract No. DE-FG26-03NT41795 are reported for the period September 1, 2004 to August 31, 2005. This contract is with the University of Kentucky Research Foundation, which supports work with the University of Kentucky Center for Applied Energy Research and The Pennsylvania State University Energy Institute. The worked described was part of a project entitled ''Advanced Gasification By-Product Utilization''. This work involves the development of technologies for the separation and characterization of coal gasification slags from operating gasification units, activation of these materials to increase mercury and nitrogen oxide capture efficiency, assessment of these materials as sorbents for mercury and nitrogen oxides, and characterization of these materials for use as polymer fillers.
Book Synopsis Demonstration of An Integrated Approach to Mercury Control at Lee Station by :
Download or read book Demonstration of An Integrated Approach to Mercury Control at Lee Station written by and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: General Electric (GE) has developed an approach whereby native mercury reduction on fly ash can be improved by optimizing the combustion system. This approach eliminates carbon-rich areas in the combustion zone, making the combustion process more uniform, and allows increasing carbon content in fly ash without significant increase in CO emissions. Since boiler excess O2 can be also reduced as a result of optimized combustion, this process reduces NO(subscript x) emissions. Because combustion optimization improves native mercury reduction on fly ash, it can reduce requirements for activated carbon injection (ACI) when integrated with sorbent injection for more efficient mercury control. The approach can be tailored to specific unit configurations and coal types for optimal performance. This report describes results of a U.S. DOE sponsored project designed to evaluate the effect of combustion conditions on 'native' mercury capture on fly ash and integrate combustion optimization for improved mercury and NO(subscript x) reduction with ACI. The technology evaluation took place in Lee Station Unit 3 located in Goldsboro, NC and operated by Progress Energy. Unit 3 burns a low-sulfur Eastern bituminous coal and is a 250 MW opposed-wall fired unit equipped with an ESP with a specific collection area of 249 ft2/kacfm. Unit 3 is equipped with SO3 injection for ESP conditioning. The technical goal of the project was to evaluate the technology's ability to achieve 70% mercury reduction below the baseline emission value of 2.9 lb/TBtu, which was equivalent to 80% mercury reduction relative to the mercury concentration in the coal. The strategy to achieve the 70% incremental improvement in mercury removal in Unit 3 was (1) to enhance 'naturally' occurring fly ash mercury capture by optimizing the combustion process and using duct humidification to reduce flue gas temperatures at the ESP inlet, and (2) to use ACI in front of the ESP to further reduce mercury emissions. The program was comprised of field and pilot-scale tests, engineering studies and consisted of eight tasks. As part of the program, GE conducted pilot-scale evaluation of sorbent effect on mercury reduction, supplied and installed adjustable riffle boxes to assist in combustion optimization, performed combustion optimization, supplied mobile sorbent injection and flue gas humidification systems, conducted CFD modeling of sorbent injection and flue gas humidification, and performed mercury testing including a continuous 30-day sorbent injection trial. Combustion optimization was the first step in reduction of mercury emissions. Goals of combustion optimization activities were to improve 'native' mercury capture on fly ash and reduce NO(subscript x). Combustion optimization included balancing of coal flow through individual burners to eliminate zones of carbon-rich combustion, air flow balancing, and burner adjustments. As part of the project, the original riffle boxes were replaced with Foster-Wheeler's adjustable riffle boxes to allow for biasing the coal flow between the coal pipes. A 10-point CO/O2/NO(subscript x) grid was installed in the primary superheater region of the back pass to assist in these activities. Testing of mercury emissions before and after combustion optimization demonstrated that mercury emissions were reduced from 2.9 lb/TBtu to 1.8 lb/TBtu due to boiler operation differences in conjunction with combustion optimization, a 38% improvement in 'native' mercury capture on fly ash. Native mercury reduction from coal was (almost equal to)42% at baseline conditions and 64% at optimized combustion conditions. As a result of combustion optimization NO(subscript x) emissions were reduced by 18%. A three-dimensional CFD model was developed to study the flow distribution and sorbent injection in the post air heater duct in Lee Station Unit 3. Modeling of the flow pattern exiting the air pre-heater demonstrated that because of the duct transition from a circular opening at the exit of air-pre-heater to a rectangular ESP inlet duct, flow separation occurred at the corners after the transition. Modeling also demonstrated that the flow was severely biased from the South side to the North side due to the bend of the duct. Results of CFD modeling were used to design lances for better sorbent distribution across the ESP inlet duct. Modeling of water injection demonstrated that because of flue gas temperature biasing, the droplet evaporation rate was slower on the North side than that on the South side of the duct. Modeling suggested that an improvement of water droplet evaporation could be achieved by closing the lance on the North side where flue gas temperatures were lower. Preliminary evaluation of the effect of carbon-based sorbents on mercury reduction took place in a 1 MBtu/hr (300 kW) Boiler Simulator Facility using the same coal as fired at Lee Station.
Book Synopsis Development of Superior Sorbents for Separation of CO2 from Flue Gas at a Wide Temperature Range During Coal Combustion by :
Download or read book Development of Superior Sorbents for Separation of CO2 from Flue Gas at a Wide Temperature Range During Coal Combustion written by and published by . This book was released on 2002 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A number basic sorbents based on CaO were synthesized, characterized with novel techniques and tested for sorption of CO2 and selected gas mixtures simulating flue gas from coal fired boilers. Our studies resulted in highly promising sorbents which demonstrated zero affinity for N2, O2, SO2, and NO very low affinity for water, ultrahigh CO2 sorption capacities, and rapid sorption characteristics, CO2 sorption at a very wide temperature range, durability, and low synthesis cost. One of the 'key' characteristics of the proposed materials is the fact that we can control very accurately their basicity (optimum number of basic sites of the appropriate strength) which allows for the selective chemisorption of CO2 at a wide range of temperatures. These unique characteristics of this family of sorbents offer high promise for development of advanced industrial sorbents for the effective CO2 removal.
Book Synopsis Mercury Control by : Evan J. Granite
Download or read book Mercury Control written by Evan J. Granite and published by John Wiley & Sons. This book was released on 2015-01-20 with total page 479 pages. Available in PDF, EPUB and Kindle. Book excerpt: This essential handbook and ready reference offers a detailed overview of the existing and currently researched technologies available for the control of mercury in coal-derived gas streams and that are viable for meeting the strict standards set by environmental protection agencies. Written by an internationally acclaimed author team from government agencies, academia and industry, it details US, EU, Asia-Pacific and other international perspectives, regulations and guidelines.
Book Synopsis Evaluation of Nanocrystalline Sorbents for Mercury Removal from Coal Gasifier Fuel by : Raja A. Jadhav
Download or read book Evaluation of Nanocrystalline Sorbents for Mercury Removal from Coal Gasifier Fuel written by Raja A. Jadhav and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Development of Novel Activated Carbon-based Adsorbents for Control of Mercury Emissions from Coal-fired Power Plants by :
Download or read book Development of Novel Activated Carbon-based Adsorbents for Control of Mercury Emissions from Coal-fired Power Plants written by and published by . This book was released on 1998 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: The overall objective of this study is to evaluate pertinent design and operational parameters that would enable successful application of adsorption-based technologies for the reduction of mercury emissions from coal-fired power plants. The first part of the study will evaluate the most suitable impregnate for its ability to enhance the adsorptive capacity of activated carbon for mercury vapor under various process conditions. The second part of the study will evaluate the rate of mercury uptake (adsorption kinetics) by several impregnated activated carbons. Concerned with the ability of the adsorbed mercury to migrate back into the environment once saturated adsorbent is removed from the system, the study will also determine the fate of mercury adsorbed on these impregnated carbons.
