Download Axial Compressive Behavior Of Frp Concrete Steel Double Skin Tubular Columns full books in PDF, epub, and Kindle. Read online Axial Compressive Behavior Of Frp Concrete Steel Double Skin Tubular Columns ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis Axial Compressive Behavior of FRP-concrete-steel Double-skin Tubular Columns by : Butje Alfonsius Louk Fanggi
Download or read book Axial Compressive Behavior of FRP-concrete-steel Double-skin Tubular Columns written by Butje Alfonsius Louk Fanggi and published by . This book was released on 2015 with total page 306 pages. Available in PDF, EPUB and Kindle. Book excerpt: "A new type of composite structural system has been proposed in terms of FRP-concrete-steel double-skin tubular columns (DSTCs). This composite system consists of a steel tube inside, an FRP tube outside with concrete in between, and it combines the advantages of all three materials to achieve a high-performance structural member. This thesis is aimed at developing an improved understanding of the axial compressive behavior of DSTCs. To this end, six experimental studies were undertaken at the University of Adelaide. In each of these studies, the key parameters that influence the axial compressive behavior of DSTCs were identified and investigated. The results of these experimental studies indicate that concrete in a DSTC system is confined effectively by FRP and steel tubes. Both the normal-and high-strength concrete DSTCs exhibited a highly ductile compressive behavior under monotonic and cyclic axial compression. However, it is found that, for a given nominal confinement ratio, an increase in the concrete strength results in a decrease in the ultimate axial strain of DSTCs. The results also indicate that increasing the inner steel tube diameter leads to an increase in the ultimate axial stress and strain of concrete in DSTCs. It is observed that the concrete-filling of the inner steel tubes of DSTCs results in an increase in the compressive strength and a slight decrease in the ultimate axial strain of concrete in DSTCs, compared to the values observed in companion specimens with hollow inner steel tubes. It is also observed that cyclically loaded normal-strength concrete (NSC) DSTCs developed similar strength and strain enhancement ratios to those of monotonically loaded NSC DSTCs. The results also show that concrete in hollow DSTCs manufactured with square inner steel tubes develops significantly lower ultimate axial stresses and strains than those of concrete in companion hollow DSTCs with circular inner steel tubes. It is found, however, that the performance of these specimens improves dramatically when the square inner steel tube is filled with concrete. Apart from these experimental studies, this thesis also presents analytical models that were developed to predict the compressive strength and ultimate axial strain of concrete in DSTCs. The first of these models was developed to predict the compressive strength and ultimate axial strain of concrete in hollow circular DSTCs. After undertaking additional studies to expand the test database of square and concrete-filled DSTCs a second model that is applicale both circular and square and hollow and concrete-filled DSTCs was proposed. Comparison with experimental test results show that of the proposed models are in close agreement with the test results, and the models provide improved accuracy compared to the existing models." -- abstract, pages vii-viii.
Book Synopsis Development of Ultra-High Performance Concrete against Blasts by : Chengqing Wu
Download or read book Development of Ultra-High Performance Concrete against Blasts written by Chengqing Wu and published by Woodhead Publishing. This book was released on 2018-03-19 with total page 424 pages. Available in PDF, EPUB and Kindle. Book excerpt: Development of Ultra-High Performance Concrete against Blasts: From Materials to Structures presents a detailed overview of UHPC development and its related applications in an era of rising terrorism around the world. Chapters present case studies on the novel development of the new generation of UHPC with nano additives. Field blast test results on reinforced concrete columns made with UHPC and UHPC filled double-skin tubes columns are also presented and compiled, as is the residual load-carrying capacities of blast-damaged structural members and the exceptional performance of novel UHPC materials that illustrate its potential in protective structural design. As a notable representative, ultra-high performance concrete (UHPC) has now been widely investigated by government agencies and universities. UHPC inherits many positive aspects of ultra-high strength concrete (UHSC) and is equipped with improved ductility as a result of fiber addition. These features make it an ideal construction material for bridge decks, storage halls, thin-wall shell structures, and other infrastructure because of its protective properties against seismic, impact and blast loads. Focuses on the principles behind UHPC production, properties, design and detailing aspects Presents a series of case studies and filed blast tests on columns and slabs Focuses on applications and future developments
Download or read book FRP written by J. G. Teng and published by John Wiley & Sons. This book was released on 2002 with total page 280 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fibre-reinforced polymer (FRP) composites are used to strengthen reinforced concrete (RC) structures. A large amount of research now exists on this. This book brings together all existing research into one volume.
Book Synopsis Composites for Construction by : Lawrence C. Bank
Download or read book Composites for Construction written by Lawrence C. Bank and published by John Wiley & Sons. This book was released on 2006-07-21 with total page 572 pages. Available in PDF, EPUB and Kindle. Book excerpt: The first textbook on the design of FRP for structural engineering applications Composites for Construction is a one-of-a-kind guide to understanding fiber-reinforced polymers (FRP) and designing and retrofitting structures with FRP. Written and organized like traditional textbooks on steel, concrete, and wood design, it demystifies FRP composites and demonstrates how both new and retrofit construction projects can especially benefit from these materials, such as offshore and waterfront structures, bridges, parking garages, cooling towers, and industrial buildings. The code-based design guidelines featured in this book allow for demonstrated applications to immediately be implemented in the real world. Covered codes and design guidelines include ACI 440, ASCE Structural Plastics Design Manual, EUROCOMP Design Code, AASHTO Specifications, and manufacturer-published design guides. Procedures are provided to the structural designer on how to use this combination of code-like documents to design with FRP profiles. In four convenient sections, Composites for Construction covers: * An introduction to FRP applications, products and properties, and to the methods of obtaining the characteristic properties of FRP materials for use in structural design * The design of concrete structural members reinforced with FRP reinforcing bars * Design of FRP strengthening systems such as strips, sheets, and fabrics for upgrading the strength and ductility of reinforced concrete structural members * The design of trusses and frames made entirely of FRP structural profiles produced by the pultrusion process
Book Synopsis Concrete-Filled Double Skin Steel Tubular Column with Hybrid Fibre Reinforced Polymer by : Kok Keong Choong
Download or read book Concrete-Filled Double Skin Steel Tubular Column with Hybrid Fibre Reinforced Polymer written by Kok Keong Choong and published by Springer Nature. This book was released on 2021-07-06 with total page 81 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book highlights the residual strength of the CFDST column, that can be used to determine the most suitable repair method in order to retrofit the column. The book elaborates on the behavior of CFDST column after being exposed to fire. This book also discusses the effectiveness of repair method using single and Hybrid Fibre Reinforced Polymer (FRP) of fire-damaged CFDST columns. It concludes by taking a look at different parameters such as thickness of outer steel tube and fire exposure time as factors affecting thermal properties/stability.
Book Synopsis ACI 440. 2R-17 Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures by : ACI Committee 440
Download or read book ACI 440. 2R-17 Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures written by ACI Committee 440 and published by . This book was released on 2017-04-27 with total page 110 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Fourth International Conference on Advances in Steel Structures by : Z Y Shen
Download or read book Fourth International Conference on Advances in Steel Structures written by Z Y Shen and published by Elsevier. This book was released on 2005-06-07 with total page 963 pages. Available in PDF, EPUB and Kindle. Book excerpt: This two volume proceedings contains 11 invited keynote papers, 33 invited papers, and 225 contributed papers presented at the Fourth International Conference on Advances in Steel Structures (ICASS '05) held on 13-15 June 2005 in Shanghai, China. ICASS provides a forum for discussion and dissemination by researchers and designers of recent advances in the analysis, behaviour, design and construction of steel structures. Contributions to the papers came from 22 countries around the world and cover a wide spectrum of topics including: Constructional Steel, Hybrid Structures, Nonferrous Metals, Analysis of Beams and Columns, Computations, Frames, Design, Space Structures, Fabrication, along with a variety of other key subjects presented at the conference.
Book Synopsis Concrete Composite Columns by : Chong Rong
Download or read book Concrete Composite Columns written by Chong Rong and published by Elsevier. This book was released on 2022-11-25 with total page 435 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete Composite Columns: Behavior and Design focuses on confined concrete and establishes analytical methods for each composite column. The volume moves beyond existing resources to study the relationship between existing composite structures and design methods for the sectional form of a concrete composite structure. Chapters cover the failure criteria of concrete, confined concrete types, models, including axial stress prediction, analysis and design-oriented constitutive models, the design and analysis of section form, axial and seismic behaviors of concrete composite columns, the seismic design of concrete composite columns, and the engineering application. This book offers a practical solution to students, researchers, and engineers working with both steel and FRP-confined concrete composite columns. Focuses on confined concrete and provides analytical methods for composite columns Discusses different types of composite columns, including FRP and steel-concrete composites Considers the construction method and confining forces in composite concrete columns Details confined concrete from basic theoretical analysis to seismic behaviors and design methods Provides a solution to students, researchers, and engineers working with confined composite columns
Book Synopsis Sustainable Practices and Innovations in Civil Engineering by : S. Ramanagopal
Download or read book Sustainable Practices and Innovations in Civil Engineering written by S. Ramanagopal and published by Springer Nature. This book was released on 2020-08-28 with total page 351 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book presents the select proceedings of the International Conference on Sustainable Practices and Innovations in Civil Engineering (SPICE 2019). The chapters discuss emerging and current research in sustainability in different areas of civil engineering, which aim to provide solutions to sustainable development. The contents are broadly divided into the following six categories: (i) structural systems, (ii) environment and water resource systems, (iii) construction technologies, (iv)geotechnical systems, (v) innovative building materials, and (vi) transportation. This book will be of potential interest for students, researchers, and practitioners working in sustainable civil engineering related fields.
Book Synopsis Strengthening and Rehabilitation of Civil Infrastructures Using Fibre-Reinforced Polymer (FRP) Composites by : L C Hollaway
Download or read book Strengthening and Rehabilitation of Civil Infrastructures Using Fibre-Reinforced Polymer (FRP) Composites written by L C Hollaway and published by Elsevier. This book was released on 2008-07-18 with total page 415 pages. Available in PDF, EPUB and Kindle. Book excerpt: The repair of deteriorated, damaged and substandard civil infrastructures has become one of the most important issues for the civil engineer worldwide. This important book discusses the use of externally-bonded fibre-reinforced polymer (FRP) composites to strengthen, rehabilitate and retrofit civil engineering structures, covering such aspects as material behaviour, structural design and quality assurance. The first three chapters of the book review structurally-deficient civil engineering infrastructure, including concrete, metallic, masonry and timber structures. FRP composites used in rehabilitation and surface preparation of the component materials are also reviewed. The next four chapters deal with the design of FRP systems for the flexural and shear strengthening of reinforced concrete (RC) beams and the strengthening of RC columns. The following two chapters examine the strengthening of metallic and masonry structures with FRP composites. The last four chapters of the book are devoted to practical considerations in the flexural strengthening of beams with unstressed and prestressed FRP plates, durability of externally bonded FRP composite systems, quality assurance and control, maintenance, repair, and case studies. With its distinguished editors and international team of contributors, Strengthening and rehabilitation of civil infrastructures using fibre-reinforced polymer (FRP) composites is a valuable reference guide for engineers, scientists and technical personnel in civil and structural engineering working on the rehabilitation and strengthening of the civil infrastructure. Reviews the use of fibre-reinforced polymer (FRP) composites in structurally damaged and sub-standard civil engineering structures Examines the role and benefits of fibre-reinforced polymer (FRP) composites in different types of structures such as masonry and metallic strengthening Covers practical considerations including material behaviour, structural design and quality assurance
Book Synopsis Hybrid FRP-concrete-steel Double-skin Tubular Columns Under Axial Cyclic Compression by : Yubo Cao
Download or read book Hybrid FRP-concrete-steel Double-skin Tubular Columns Under Axial Cyclic Compression written by Yubo Cao and published by . This book was released on 2009 with total page 200 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Advances in Construction Materials and Sustainable Environment by : Ashok Kumar Gupta
Download or read book Advances in Construction Materials and Sustainable Environment written by Ashok Kumar Gupta and published by Springer Nature. This book was released on 2021-12-14 with total page 1041 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book comprises select papers presented at the International Conference on Construction Materials and Environment (ICCME 2020). The topics discussed revolve around the identification and utilization of novel construction materials primarily in the areas of structural engineering, geotechnical engineering, transportation engineering, and environmental engineering. The volume presents a compilation of thoroughly studied and utilized sustainable construction materials in different areas of civil engineering. Newly developed testing methodologies, physical modelling methods, numerical studies, and other latest techniques discussed in this book can prove to be useful for researchers and practitioners across the globe.
Book Synopsis Concrete-Filled Double-Skin Steel Tubular Columns by : Mostafa Fahmi Hassanein
Download or read book Concrete-Filled Double-Skin Steel Tubular Columns written by Mostafa Fahmi Hassanein and published by Elsevier. This book was released on 2023-02-16 with total page 360 pages. Available in PDF, EPUB and Kindle. Book excerpt: Concrete-Filled Double-Skin Steel Tubular Columns: Behavior and Design provides a thorough review of the recent advances on the behaviour and design of concrete-filled double-skin steel tubular (CFDST) columns. Drawing on their extensive knowledge and research, the authors cover topics such as different CFDST columns under axial compression, innovative techniques including the use of rubberised concrete, columns with different cross-sections, and steel material envelops and failure modes. This book is an overview of research carried out by this highly experienced and leading research group with specialist knowledge in the topic. It is an invaluable resource for researchers, graduates and post-graduate civil engineers and civil engineering designers. Provides a comprehensive overview of advances on the behaviour and design of concrete-filled double-skin steel tubular (CFDST) columns over the past decade Gives deep-dive explanation of important concepts such as the void ratio which makes these girders different from conventional concrete-filled steel tubular (CFST) columns Explains the failure modes of short and slender columns under compression, with detailed illustrations and photos from both real-life and virtual tests performed by the authors Presents in-depth analysis of the ultimate strengths of CFDST columns with different steel envelops and concrete infills Makes a detailed comparison with available international codes, such as Eurocode 3, and provides recommendations for future studies Discusses new innovative confining stress-based design for different types of CFDST short columns
Download or read book Steel & Composite Structures written by and published by Research Publishing Service. This book was released on 2010 with total page 145 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Recent Advances in Computational and Experimental Mechanics, Vol—I by : D. Maity
Download or read book Recent Advances in Computational and Experimental Mechanics, Vol—I written by D. Maity and published by Springer Nature. This book was released on 2022-01-01 with total page 656 pages. Available in PDF, EPUB and Kindle. Book excerpt: This book (Vol. - I) presents select proceedings of the first Online International Conference on Recent Advances in Computational and Experimental Mechanics (ICRACEM 2020) and focuses on theoretical, computational and experimental aspects of solid and fluid mechanics. Various topics covered are computational modelling of extreme events; mechanical modelling of robots; mechanics and design of cellular materials; mechanics of soft materials; mechanics of thin-film and multi-layer structures; meshfree and particle based formulations in continuum mechanics; multi-scale computations in solid mechanics, and materials; multiscale mechanics of brittle and ductile materials; topology and shape optimization techniques; acoustics including aero-acoustics and wave propagation; aerodynamics; dynamics and control in micro/nano engineering; dynamic instability and buckling; flow-induced noise and vibration; inverse problems in mechanics and system identification; measurement and analysis techniques in nonlinear dynamic systems; multibody dynamical systems and applications; nonlinear dynamics and control; stochastic mechanics; structural dynamics and earthquake engineering; structural health monitoring and damage assessment; turbomachinery noise; vibrations of continuous systems, characterization of advanced materials; damage identification and non-destructive evaluation; experimental fire mechanics and damage; experimental fluid mechanics; experimental solid mechanics; measurement in extreme environments; modal testing and dynamics; experimental hydraulics; mechanism of scour under steady and unsteady flows; vibration measurement and control; bio-inspired materials; constitutive modelling of materials; fracture mechanics; mechanics of adhesion, tribology and wear; mechanics of composite materials; mechanics of multifunctional materials; multiscale modelling of materials; phase transformations in materials; plasticity and creep in materials; fluid mechanics, computational fluid dynamics; fluid-structure interaction; free surface, moving boundary and pipe flow; hydrodynamics; multiphase flows; propulsion; internal flow physics; turbulence modelling; wave mechanics; flow through porous media; shock-boundary layer interactions; sediment transport; wave-structure interaction; reduced-order models; turbo-machinery; experimental hydraulics; mechanism of scour under steady and unsteady flows; applications of machine learning and artificial intelligence in mechanics; transport phenomena and soft computing tools in fluid mechanics. The contents of these two volumes (Volumes I and II) discusses various attributes of modern-age mechanics in various disciplines, such as aerospace, civil, mechanical, ocean engineering and naval architecture. The book will be a valuable reference for beginners, researchers, and professionals interested in solid and fluid mechanics and allied fields.
Book Synopsis 10th International Conference on FRP Composites in Civil Engineering by : Alper Ilki
Download or read book 10th International Conference on FRP Composites in Civil Engineering written by Alper Ilki and published by Springer Nature. This book was released on 2021-11-26 with total page 2516 pages. Available in PDF, EPUB and Kindle. Book excerpt: This volume highlights the latest advances, innovations, and applications in the field of FRP composites and structures, as presented by leading international researchers and engineers at the 10th International Conference on Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering (CICE), held in Istanbul, Turkey on December 8-10, 2021. It covers a diverse range of topics such as All FRP structures; Bond and interfacial stresses; Concrete-filled FRP tubular members; Concrete structures reinforced or pre-stressed with FRP; Confinement; Design issues/guidelines; Durability and long-term performance; Fire, impact and blast loading; FRP as internal reinforcement; Hybrid structures of FRP and other materials; Materials and products; Seismic retrofit of structures; Strengthening of concrete, steel, masonry and timber structures; and Testing. The contributions, which were selected by means of a rigorous international peer-review process, present a wealth of exciting ideas that will open novel research directions and foster multidisciplinary collaboration among different specialists.
Book Synopsis Behavior of Large-scale Hybrid FRP-concrete-steel Double-skin Tubular Columns Subjected to Concentric and Eccentric Compression by : Pan Xie
Download or read book Behavior of Large-scale Hybrid FRP-concrete-steel Double-skin Tubular Columns Subjected to Concentric and Eccentric Compression written by Pan Xie and published by . This book was released on 2018 with total page 383 pages. Available in PDF, EPUB and Kindle. Book excerpt:
