Author : Matthew Gadinski
Publisher :
ISBN 13 :
Total Pages : pages
Book Rating : 4.:/5 (943 download)
Book Synopsis Understanding the Effects of Defect Modification on the Structure and Properties of Fluorinated Polymers and Implications for Capacitive Energy Storage Technologies by : Matthew Gadinski
Download or read book Understanding the Effects of Defect Modification on the Structure and Properties of Fluorinated Polymers and Implications for Capacitive Energy Storage Technologies written by Matthew Gadinski and published by . This book was released on 2015 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: As the world begins to turn to alternative energy technologies and our electronic devices have become more both mobile and integral to everyday life, increasing interest has been focused on energy storage technologies. Capacitors are one of these energy storage technologies that utilize the polarization of an insulating material sandwiched by two electrodes as a means to store electric charge. Polymers are a preferred dielectric material for capacitors because of both their performance and practicality. However, polymer dielectrics are limited in energy density by low dielectric constant, and high loss at elevated temperature. This work aims to address these issues in order to enable polymer dielectrics for future applications and demands. As most polymer tend to have low dielectric constants (~2-3), but impressive breakdown strengths, only a moderate improvement in dielectric constant has the potential to vastly improve the energy density of polymer capacitors. As such tremendous interest has been placed on poly(vinylidene fluoride) (PVDF) which has a dielectric of 10+ due to the highly polar C-F bonds of its backbone. To improve PVDF's performance defect monomers have been introduced to tailor the polymorphic crystalline phase to tune its properties. Additionally, this defect modification has implications for piezoelectric, electrocaloric, and thermoelectric applications of PVDFIn Chapter 2 a copolymer of VDF and bromotrifluoroethylene (BTFE) was produced. The effect of BTFE on the structure and dielectric properties of the resulting copolymer had not been previously evaluated, and its synthesis allowed for the comparison to previously reported VDF based copolymers including P(VDF-CTFE) and P(VDF-HFP). Through 19F NMR it was determined due to reactivity ratio differences of BTFE in comparison to previously explored copolymers, BTFE during synthesis is much more likely to link with itself. This results in long runs of BTFE-BTFE defects along with isolated single defects. These long runs are found to have dramatic effects on the distribution of chain conformations determined from FTIR, the melting temperature and total crystallinity determined by DSC, and the crystallite size, lattice spacing, and crystalline phase as determined by XRD. These results indicate that P(VDF-BTFE) has a mix of both included (single) and excluded defects (runs of defects) that rapidly inhibit crystallinity and alter phase. The dielectric analysis also confirmed this by a broadening of the Tg peak in the temperature dependent dielectric spectroscopy with increasing BTFE content in the monomer feed indicative of expansion of the interlamellar region due to defect exclusion.Chapter 3 explores P(VDF-BTFE) copolymers for capacitive energy storage. Due to the rapid decrease in crystallinity only low concentration copolymers (>2 mol %) BTFE were used. This was ultimately a result of stretching being required for high energy density to be exhibited. The 0.5 mol% BTFE copolymer samples was found to possess a discharge energy density of 20.8 J/cm3 at 750 MV/m along with the highest breakdown strength of any reported PVDF based copolymer. It was found that for this small amount of defect monomer the [gamma] phase of PVDF was stabilized and mixed with [beta] phase and along with small crystallite size accounted for the high breakdown strength and energy density. Additionally, by utilizing only a small amount of defect monomer the decrease in crystallinity and melting temperature observed in previously examined PVDF copolymers was avoided.Chapter 4 examines a terpolymer of VDF, trifluoroethylene (TrFE), and chlorotrifluoroethylene (CTFE). The terpolymers of VDF have gained extensive interest as the use of the two defect monomer increases the dielectric constant to 40+ along with altering the polarization behavior from a normal ferroelectric to a relaxor ferroelectric characterized by a slim hysteresis loop. The current understanding of this behavior suggests that only the size of the third bulky monomer (CTFE in this case) determines whether a single hysteresis (SHL) or double hysteresis loop (DHL) will develop. This chapter shows that for a single composition of the terpolymer normal ferroelectric, SHL, and DHL behavior can be tuned through processing of the film. This was rationalized as films give long times to crystallize developed large ferroelectric domains within a paraelectric matrix resulting in the DHL behavior due to reversible switching of these domains. While if these films were stretched below the Tc SHL behavior was observed as this had the effect of dispersing these domains within the crystal. Chapter 5 changes focus to high temperature performance of polymer capacitors. The primary strategy to enable high temperature polymer capacitors has been the utilization of high Tg polymers because of their thermal stability. While these polymers have demonstrated stable dielectric properties at low field and high breakdown strengths at elevated temperatures, the high field loss limits their use at even mildly elevated temperature well below Tg. Additionally, these polymers are expensive, brittle, and difficult to process, essentially defeating some of the primary reasons for utilizing a polymer in the first place. This chapter examines a commercially available, extrudable, high temperature fluoropolymer, known as polychlorotrifluoroethylene (PCTFE). The same defect monomer discussed with PVDF above. While this polymer showed comparable performance to BOPP at room temperature, it showed equally susceptible to high field loss at elevated temperature. However, the chlorine of the monomers allow for crosslinking of this polymer by commercially used peroxide/co-agent chemistry. Crosslinking lead to a substantial improvement of the crosslinked film over the pristine polymer, and superior energy density to the commercial high Tg polymers up to 150 °C. The reason for the improvement was found to be the formation of chemical defects produced during the crosslinking that were excluded from the crystalline phase. Through TSDC it was found that these defects concentrated in the interlamellar region led to a substantial enhancement of the charge trapping properties of this relaxation.
