Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
Heat Transfer Analysis For Fixed Cst And Rf Columns
Download Heat Transfer Analysis For Fixed Cst And Rf Columns full books in PDF, epub, and Kindle. Read online Heat Transfer Analysis For Fixed Cst And Rf Columns ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis HEAT TRANSFER ANALYSIS FOR FIXED CST AND RF COLUMNS. by :
Download or read book HEAT TRANSFER ANALYSIS FOR FIXED CST AND RF COLUMNS. written by and published by . This book was released on 2007 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In support of a small column ion exchange (SCIX) process for the Savannah River Site waste processing program, transient and steady state two-dimensional heat transfer models have been constructed for columns loaded with cesium-saturated crystalline silicotitanate (CST) or spherical Resorcinol-Formaldehyde (RF) beads and 6 molar sodium tank waste supernate. Radiolytic decay of sorbed cesium results in heat generation within the columns. The models consider conductive heat transfer only with no convective cooling and no process flow within the columns (assumed column geometry: 27.375 in ID with a 6.625 in OD center-line cooling pipe). Heat transfer at the column walls was assumed to occur by natural convection cooling with 35 C air. A number of modeling calculations were performed using this computational heat transfer approach. Minimal additional calculations were also conducted to predict temperature increases expected for salt solution processed through columns of various heights at the slowest expected operational flow rate of 5 gpm. Results for the bounding model with no process flow and no active cooling indicate that the time required to reach the boiling point of (almost equal to)130 C for a CST-salt solution mixture containing 257 Ci/liter of Cs-137 heat source (maximum expected loading for SCIX applications) at 35 C initial temperature is about 6 days. Modeling results for a column actively cooled with external wall jackets and the internal coolant pipe (inlet coolant water temperature: 25 C) indicate that the CST column can be maintained non-boiling under these conditions indefinitely. The results also show that the maximum temperature of an RF-salt solution column containing 133 Ci/liter of Cs-137 (maximum expected loading) will never reach boiling under any conditions (maximum predicted temperature without cooling: 88 C). The results indicate that a 6-in cooling pipe at the center of the column provides the most effective cooling mechanism for reducing the maximum temperature with either ion exchange material. Sensitivity calculations for the RF resin porosity, the ambient external column temperature, and the cooling system configuration were performed under the baseline conditions to assess the impact of these parameters on the maximum temperatures. It is noted that the cooling mechanism at the column boundary (forced versus natural convection) and the cooling system configuration significantly impact the maximum temperatures. The analysis results provide quantitative information associated with process temperature control requirements and management of the SCIX column.
Book Synopsis Heat Transfer Analysis for a Fixed CST Column by :
Download or read book Heat Transfer Analysis for a Fixed CST Column written by and published by . This book was released on 2004 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: In support of a small column ion exchange (SCIX) process for the Savannah River Site waste processing program, a transient two-dimensional heat transfer model that includes the conduction process neglecting the convection cooling mechanism inside the crystalline silicotitanate (CST) column has been constructed and heat transfer calculations made for the present design configurations. For this situation, a no process flow condition through the column was assumed as one of the reference conditions for the simulation of a loss-of-flow accident. A series of the modeling calculations has been performed using a computational heat transfer approach. Results for the baseline model indicate that transit times to reach 130 degrees Celsius maximum temperature of the CST-salt solution column are about 96 hours when the 20-in CST column with 300 Ci/liter heat generation source and 25 degrees Celsius initial column temperature is cooled by natural convection of external air as a primary heat transfer mechanism. The modeling results for the 28-in column equipped with water jacket systems on the external wall surface of the column and water coolant pipe at the center of the CST column demonstrate that the column loaded with 300 Ci/liter heat source can be maintained non-boiling indefinitely. Sensitivity calculations for several alternate column sizes, heat loads of the packed column, engineered cooling systems, and various ambient conditions at the exterior wall of the column have been performed under the reference conditions of the CST-salt solution to assess the impact of those parameters on the peak temperatures of the packed column for a given transient time. The results indicate that a water-coolant pipe at the center of the CST column filled with salt solution is the most effective one among the potential design parameters related to the thermal energy dissipation of decay heat load. It is noted that the cooling mechanism at the wall boundary of the column has significant impact on maximum and wall temperatures of the column. In addition, the results computed by the present model were verified by the theoretical results. The analysis results will provide quantitative information associated with the process heat control and management of the CST base design. For example, transient responses of the CST system under a loss-of-flow accident condition will provide safety design information for an emergency cooling system of the column.
Book Synopsis Heat Transfer Calculations for Normal Operations of a Fixed CST Bed Column by :
Download or read book Heat Transfer Calculations for Normal Operations of a Fixed CST Bed Column written by and published by . This book was released on 2001 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: In support of the crystalline silicotitanate (CST) ion exchange project of High-Level Waste (HLW) Process Engineering, heat transfer calculations have been made for a fully-loaded CST column during abnormal and normal operating conditions. The objective of the present work is to compute temperature distributions across the column when there is steady flow of salt solution through the CST column under normal conditions of the process operations.
Book Synopsis Heat Transfer Calculations for a Fixed CST Bed Column by :
Download or read book Heat Transfer Calculations for a Fixed CST Bed Column written by and published by . This book was released on 2001 with total page 5 pages. Available in PDF, EPUB and Kindle. Book excerpt: In support of the crystalline silicotitanate (CST) ion exchange project of High-Level Waste (HLW) Process Engineering, a transient two-dimensional heat transfer model that includes the conduction process neglecting the convection cooling mechanism inside the CST column has been constructed and heat transfer calculations made for the present design configurations. For this situation, a no process flow condition through the column was assumed as one of the reference conditions for the simulation of a loss-of-flow accident. The modeling and calculations were performed using a computational heat transfer approach.
Book Synopsis Thermal Modeling Analysis of CST Media in the Small Column Ion Exchange Project by :
Download or read book Thermal Modeling Analysis of CST Media in the Small Column Ion Exchange Project written by and published by . This book was released on 2010 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: Models have been developed to simulate the thermal characteristics of Crystalline Silicotitanate (CST) ion exchange media fully loaded with radioactive cesium in a column configuration and distributed within a waste storage tank. This work was conducted to support the Small Column Ion Exchange (SCIX) program which is focused on processing dissolved, high-sodium salt waste for the removal of specific radionuclides (including Cs-137, Sr-90, and actinides) within a High Level Waste (HLW) storage tank at the Savannah River Site. The SCIX design includes CST columns inserted and supported in the tank top risers for cesium removal. Temperature distributions and maximum temperatures across the column were calculated with a focus on process upset conditions. A two-dimensional computational modeling approach for the in-column ion-exchange domain was taken to include conservative, bounding estimates for key parameters such that the results would provide the maximum centerline temperatures achievable under the design configurations using a feed composition known to promote high cesium loading on CST. One salt processing scenario includes the transport of the loaded (and possibly ground) CST media to the treatment tank floor. Therefore, additional thermal modeling calculations were conducted using a three-dimensional approach to evaluate temperature distributions for the entire in-tank domain including distribution of the spent CST media either as a mound or a flat layer on the tank floor. These calculations included mixtures of CST with HLW sludge or loaded Monosodium Titanate (MST) media used for strontium/actinide sorption. The current full-scale design for the CST column includes one central cooling pipe and four outer cooling tubes. Most calculations assumed that the fluid within the column was stagnant (i.e. no buoyancy-induced flow) for a conservative estimate. A primary objective of these calculations was to estimate temperature distributions across packed CST beds immersed in waste supernate or filled with dry air under various accident scenarios. Accident scenarios evaluated included loss of salt solution flow through the bed (a primary heat transfer mechanism), inadvertent column drainage, and loss of active cooling in the column. The calculation results showed that for a wet CST column with active cooling through one central and four outer tubes and 35 C ambient external air, the peak temperature for the fully-loaded column is about 63 C under the loss of fluid flow accident, which is well below the supernate boiling point. The peak temperature for the naturally-cooled (no active, engineered cooling) wet column is 156 C under fully-loaded conditions, exceeding the 130 C boiling point. Under these conditions, supernate boiling would maintain the column temperature near 130 C until all supernate was vaporized. Without active engineered cooling and assuming a dry column suspended in unventilated air at 35 C, the fully-loaded column is expected to rise to a maximum of about 258 C due to the combined loss-of coolant and column drainage accidents. The modeling results demonstrate that the baseline design using one central and four outer cooling tubes provides a highly efficient cooling mechanism for reducing the maximum column temperature. Results for the in-tank modeling calculations clearly indicate that when realistic heat transfer boundary conditions are imposed on the bottom surface of the tank wall, as much as 450 gallons of ground CST (a volume equivalent to two ion exchange processing cycles) in an ideal hemispherical shape (the most conservative geometry) can be placed in the tank without exceeding the 100 C wall temperature limit. Furthermore, in the case of an evenly-distributed flat layer, the tank wall reaches the temperature limit after the ground CST material reaches a height of approximately 8 inches.
Book Synopsis TEXTBOOK OF FINITE ELEMENT ANALYSIS by : P. SESHU
Download or read book TEXTBOOK OF FINITE ELEMENT ANALYSIS written by P. SESHU and published by PHI Learning Pvt. Ltd.. This book was released on 2003-01-01 with total page 340 pages. Available in PDF, EPUB and Kindle. Book excerpt: Designed for a one-semester course in Finite Element Method, this compact and well-organized text presents FEM as a tool to find approximate solutions to differential equations. This provides the student a better perspective on the technique and its wide range of applications. This approach reflects the current trend as the present-day applications range from structures to biomechanics to electromagnetics, unlike in conventional texts that view FEM primarily as an extension of matrix methods of structural analysis. After an introduction and a review of mathematical preliminaries, the book gives a detailed discussion on FEM as a technique for solving differential equations and variational formulation of FEM. This is followed by a lucid presentation of one-dimensional and two-dimensional finite elements and finite element formulation for dynamics. The book concludes with some case studies that focus on industrial problems and Appendices that include mini-project topics based on near-real-life problems. Postgraduate/Senior undergraduate students of civil, mechanical and aeronautical engineering will find this text extremely useful; it will also appeal to the practising engineers and the teaching community.
Book Synopsis VDI Heat Atlas by : VDI Gesellschaft
Download or read book VDI Heat Atlas written by VDI Gesellschaft and published by Springer Science & Business Media. This book was released on 2010-07-21 with total page 1608 pages. Available in PDF, EPUB and Kindle. Book excerpt: For more than 50 years, the Springer VDI Heat Atlas has been an indispensable working means for engineers dealing with questions of heat transfer. Featuring 50% more content, this new edition covers most fields of heat transfer in industrial and engineering applications. It presents the interrelationships between basic scientific methods, experimental techniques, model-based analysis and their transfer to technical applications.
Book Synopsis Heat, Mass, and Momentum Transfer by : Warren M. Rohsenow
Download or read book Heat, Mass, and Momentum Transfer written by Warren M. Rohsenow and published by . This book was released on 1965 with total page 537 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Rules of Thumb for Mechanical Engineers by : J. Edward Pope
Download or read book Rules of Thumb for Mechanical Engineers written by J. Edward Pope and published by Gulf Professional Publishing. This book was released on 1997 with total page 417 pages. Available in PDF, EPUB and Kindle. Book excerpt: Fluids -- Heat transfer -- Thermodynamics -- Mechanical seals -- Pumps and compressors -- Drivers -- Gears -- Bearings -- Piping and pressure vessels -- Tribology -- Vibration -- Materials -- Stress and strain -- Fatigue -- Instrumentation -- Engineering economics.
Download or read book Ion Exchange written by C E Harland and published by Royal Society of Chemistry. This book was released on 2007-10-31 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt: Ion Exchange, 2nd Edition is a totally revised and updated version of the highly popular Monograph for Teachers, first published by The Royal Society of Chemistry in 1975. It covers the practical application of ion exchange and the synthesis of organic ion exchange resins, which have spanned nearly 60 years of development since the pioneering work of Adams and Holmes in 1935. This book covers the theory, development, and application in considerable detail and describes the history of development of ion exchange materials and the advances in their utilization in industrial processes. Key applications in such areas as water purification, hydrometallurgy, and chromatography are described and supported by chapters on the related scientific fundamentals governing equilibria and kinetics of ion exchange. Twenty-two experiments using inexpensive equipment are detailed, which not only complement a chapter dedicated to the characterization of organic exchangers, but also serve to illustrate several other pure and applied principles related to ion exchange phenomena. It is anticipated that the unique inclusion of experiments and the broad coverage of the whole text should appeal to a wide readership and offer particular relevance to practitioners in schools, colleges, and industry.
Book Synopsis Structures in Fire by : Venkatesh Kodur
Download or read book Structures in Fire written by Venkatesh Kodur and published by DEStech Publications, Inc. This book was released on 2010 with total page 1047 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Microwave Engineering by : David M. Pozar
Download or read book Microwave Engineering written by David M. Pozar and published by John Wiley & Sons. This book was released on 2011-11-22 with total page 752 pages. Available in PDF, EPUB and Kindle. Book excerpt: Pozar's new edition of Microwave Engineering includes more material on active circuits, noise, nonlinear effects, and wireless systems. Chapters on noise and nonlinear distortion, and active devices have been added along with the coverage of noise and more material on intermodulation distortion and related nonlinear effects. On active devices, there's more updated material on bipolar junction and field effect transistors. New and updated material on wireless communications systems, including link budget, link margin, digital modulation methods, and bit error rates is also part of the new edition. Other new material includes a section on transients on transmission lines, the theory of power waves, a discussion of higher order modes and frequency effects for microstrip line, and a discussion of how to determine unloaded.
Book Synopsis Handbook of Hydraulic Resistance by : I. E. Idelchik
Download or read book Handbook of Hydraulic Resistance written by I. E. Idelchik and published by . This book was released on 2005 with total page 0 pages. Available in PDF, EPUB and Kindle. Book excerpt: The handbook has been composed on the basis of processing, systematization and classification of the results of a great number of investigations published at different time. The essential part of the book is the outcome of investigations carried out by the author. The present edition of this handbook should assist in increasing the quality and efficiency of the design and usage of indutrial power engineering and other constructions and also of the devices and apparatus through which liquids and gases move.
Book Synopsis Incompressible Flow by : Ronald L. Panton
Download or read book Incompressible Flow written by Ronald L. Panton and published by John Wiley & Sons. This book was released on 2013-08-05 with total page 912 pages. Available in PDF, EPUB and Kindle. Book excerpt: The most teachable book on incompressible flow— now fully revised, updated, and expanded Incompressible Flow, Fourth Edition is the updated and revised edition of Ronald Panton's classic text. It continues a respected tradition of providing the most comprehensive coverage of the subject in an exceptionally clear, unified, and carefully paced introduction to advanced concepts in fluid mechanics. Beginning with basic principles, this Fourth Edition patiently develops the math and physics leading to major theories. Throughout, the book provides a unified presentation of physics, mathematics, and engineering applications, liberally supplemented with helpful exercises and example problems. Revised to reflect students' ready access to mathematical computer programs that have advanced features and are easy to use, Incompressible Flow, Fourth Edition includes: Several more exact solutions of the Navier-Stokes equations Classic-style Fortran programs for the Hiemenz flow, the Psi-Omega method for entrance flow, and the laminar boundary layer program, all revised into MATLAB A new discussion of the global vorticity boundary restriction A revised vorticity dynamics chapter with new examples, including the ring line vortex and the Fraenkel-Norbury vortex solutions A discussion of the different behaviors that occur in subsonic and supersonic steady flows Additional emphasis on composite asymptotic expansions Incompressible Flow, Fourth Edition is the ideal coursebook for classes in fluid dynamics offered in mechanical, aerospace, and chemical engineering programs.
Book Synopsis Capital Programming Guide by : United States. Office of Management and Budget
Download or read book Capital Programming Guide written by United States. Office of Management and Budget and published by . This book was released on 1997 with total page 116 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book Nuclear Science Abstracts written by and published by . This book was released on 1970 with total page 1774 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis The 1996 Baseline Environmental Management Report: Report by :
Download or read book The 1996 Baseline Environmental Management Report: Report written by and published by . This book was released on 1996 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
