Soliders Manual Army Testing Smart

Author :
Publisher : Jeffrey Frank Jones
ISBN 13 :
Total Pages : 604 pages
Book Rating : 4./5 ( download)

DOWNLOAD NOW!

Download or read book Publications Combined: Army Combat Fitness Test (ACFT) Training Guide, Handbook, Equipment List, Field Testing Manual & More written by and published by Jeffrey Frank Jones. This book was released on 2019-03-05 with total page 604 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over 600 total pages ... CONTENTS: Army Combat Fitness Test Training Guide Version 1.2 FIELD TESTING MANUAL Army Combat Fitness Test Version 1.4 Army Combat Fitness Test CALL NO. 18-37, September 2018 FM 7-22 ARMY PHYSICAL READINESS TRAINING, October 2012 IOC TESTING - ACFT EQUIPMENT LIST (1 X LANE REQUIREMENT) Version 1.1, 4 September 2018 ACFT Field Test Highlight Poster (Final) OVERVIEW: The Army will replace the Army Physical Fitness Test (APFT) with the Army Combat Fitness Test (ACFT) as the physical fitness test of record beginning in FY21. To accomplish this, the ACFT will be implemented in three phases. Phase 1 (Initial Operating Capability – IOC) includes a limited user Field Test with approximately 60 battalion-sized units from across all components of the Army. While the ACFT is backed by thorough scientific research and has undergone several revisions, there are still details that have not been finalized. The ACFT requires a testing site with a two-mile run course and a flat field space approximately 40 x 40 meters. The field space should be grass (well maintained and cut) or artificial turf that is generally flat and free of debris. While maintaining testing standards and requirements, commanders will make adjustments for local conditions when necessary. The start and finish point for the two-mile run course must be in close proximity to the Leg Tuck station. When test events are conducted indoors, the surface must be artificial turf only. Wood and rubberized surfaces are not authorized as they impact the speed of the Sprint-Drag-Carry. When environmental conditions prohibit outdoor testing, an indoor track may be used for the 2 Mile Run. The Test OIC or NCOIC are responsible to inspect and certify the site and determine the number of testing lanes. There should not be more than 4 Soldiers per testing group for the SPT, HRP, and SDC. The OIC or NCOIC must add additional lanes or move Soldiers to a later testing session to ensure no more than 4 Soldiers per testing group. Concerns related to Soldiers, graders, or commanders will be addressed prior to test day. The number of lanes varies by number of Soldiers testing. A 16-lane ACFT site will have the following: ACFT specific test equipment requirements: 16 hexagon/trap bars (60 pounds), each with a set of locking collars. While all NSN approved hexagon bars must weigh 60 pounds, there is always a small manufacturer’s production tolerance.The approved weight tolerance for the hexagon bar is + 2 pounds (58-62 pounds). Weight tolerance for the hexagon bar and therefore the 3 Repetition Maximum Deadlift does not include the collars. On average hexagon bar collars weigh < 2.0 pounds per pair and are considered incidental to the totalweight of the MDL weight. Approximately 3,000 lbs. of bumper plates. 16 x 10 lb. medicine ball 16 x nylon sled with pull straps. 32 x 40 lb. kettle bells. Permanent or mobile pull up bars (16 x pull-up bars at approximately 7.5 feet off the ground with,step-ups for shorter Soldiers). Common unit equipment for set-up and grading: 16 stop watches. 8 x 25m tape measures. 8 x wooden or PVC marking sticks for the SPT. One stick for every two lanes. 70 x 18” traffic cones. 50 field / dome cones. A soft, flat, dry test area approximately 40m x 40m on grass or artificial turf (half of a soccer or football field). A site that is free of any significant hazards. A preparation area (can be same as briefing area) to conduct Preparation Drill. A generally flat, measured running course with a solid, improved surface that is not more than 3 percent uphill grade and has no overall decline (start and finish must be at the same altitude).