Read Books Online and Download eBooks, EPub, PDF, Mobi, Kindle, Text Full Free.
A Composite Tracer Analysis Approach To Reservoir Characterization
Download A Composite Tracer Analysis Approach To Reservoir Characterization full books in PDF, epub, and Kindle. Read online A Composite Tracer Analysis Approach To Reservoir Characterization ebook anywhere anytime directly on your device. Fast Download speed and no annoying ads. We cannot guarantee that every ebooks is available!
Book Synopsis A Composite Tracer Analysis Approach to Reservoir Characterization by : Adedayo Stephen Oyerinde
Download or read book A Composite Tracer Analysis Approach to Reservoir Characterization written by Adedayo Stephen Oyerinde and published by . This book was released on 2005 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: In the quest for production optimization from established resources, there is a continual interest in secondary and tertiary recovery methods. The success of these enhanced recovery methods, however, rely to a large extent on a sound understanding of fluid dynamics and migration paths in the reservoir. To this end, several approaches to reservoir characterization have been put to test with varying degrees of success. The unique ability of tracers to provide direct information on preferential fluid flow paths in the reservoir, and the sensitivity of partitioning tracers to fluid saturation distribution has highlighted the prospects of a detailed reservoir characterization through interwell tracer tests. In a broad sense, analysis of interwell tracer tests fall into two categories, analytical and inverse modeling. While most of the analytical methods are laden with limiting assumptions, the method of moments boasts rigorous formulation and accurate estimates of swept volume and average saturation of bypassed oil. The inverse modeling infers permeability and saturation distribution by matching the tracer response. An extremely effective approach to the inverse modeling methods computes sensitivities based on streamlines. The accurate modeling of tracer flow requires accounting for complex phenomena such as transverse dispersion. Also, it is sometimes desired to model pertinent tracer components through compositional simulation. This necessitates the inclusion of a physical dispersion tensor and, hence, the well established finite difference formulation. In this work, we have coupled the finite difference and streamline simulation techniques for the inversion-based reservoir characterization to take advantage of the robustness of the finite difference formulation and computational efficiency of streamline simulation. We have also extended the formalism of the inversion technique for fluid distribution estimation to scenarios with mobile oil saturations and have attempted integrating the analytical and inverse-modeling techniques to facilitate detailed reservoir characterization. We have demonstrated the feasibility of our approach on both synthetic and field cases.
Book Synopsis Analysis and design of field tracers for reservoir description by : Steven Bradley Allison
Download or read book Analysis and design of field tracers for reservoir description written by Steven Bradley Allison and published by . This book was released on 1988 with total page 838 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Download or read book ספר קהלת ברוך written by and published by . This book was released on 1931 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Reservoir Characterization by : Fred Aminzadeh
Download or read book Reservoir Characterization written by Fred Aminzadeh and published by John Wiley & Sons. This book was released on 2022-01-06 with total page 578 pages. Available in PDF, EPUB and Kindle. Book excerpt: RESERVOIR CHARACTERIZATION The second volume in the series, “Sustainable Energy Engineering,” written by some of the foremost authorities in the world on reservoir engineering, this groundbreaking new volume presents the most comprehensive and updated new processes, equipment, and practical applications in the field. Long thought of as not being “sustainable,” newly discovered sources of petroleum and newly developed methods for petroleum extraction have made it clear that not only can the petroleum industry march toward sustainability, but it can be made “greener” and more environmentally friendly. Sustainable energy engineering is where the technical, economic, and environmental aspects of energy production intersect and affect each other. This collection of papers covers the strategic and economic implications of methods used to characterize petroleum reservoirs. Born out of the journal by the same name, formerly published by Scrivener Publishing, most of the articles in this volume have been updated, and there are some new additions, as well, to keep the engineer abreast of any updates and new methods in the industry. Truly a snapshot of the state of the art, this groundbreaking volume is a must-have for any petroleum engineer working in the field, environmental engineers, petroleum engineering students, and any other engineer or scientist working with reservoirs. This outstanding new volume: Is a collection of papers on reservoir characterization written by world-renowned engineers and scientists and presents them here, in one volume Contains in-depth coverage of not just the fundamentals of reservoir characterization, but the anomalies and challenges, set in application-based, real-world situations Covers reservoir characterization for the engineer to be able to solve daily problems on the job, whether in the field or in the office Deconstructs myths that are prevalent and deeply rooted in the industry and reconstructs logical solutions Is a valuable resource for the veteran engineer, new hire, or petroleum engineering student
Book Synopsis Reservoir Characterization, Modeling and Quantitative Interpretation by : Shib Sankar Ganguli
Download or read book Reservoir Characterization, Modeling and Quantitative Interpretation written by Shib Sankar Ganguli and published by Elsevier. This book was released on 2023-10-27 with total page 518 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reservoir Characterization, Modeling and Quantitative Interpretation: Recent Workflows to Emerging Technologies offers a wide spectrum of reservoir characterization techniques and technologies, focusing on the latest breakthroughs and most efficient methodologies in hydrocarbon exploration and development. Topics covered include 4D seismic technologies, AVAz inversion, fracture characterization, multiscale imaging technologies, static and dynamic reservoir characterization, among others. The content is delivered through an inductive approach, which will help readers gain comprehensive insights on advanced practices and be able to relate them to other subareas of reservoir characterization, including CO2 storage and data-driven modeling. This will be especially useful for field scientists in collecting and analyzing field data, prospect evaluation, developing reservoir models, and adopting new technologies to mitigate exploration risk. They will be able to solve the practical and challenging problems faced in the field of reservoir characterization, as it will offer systematic industrial workflows covering every aspect of this branch of Earth Science, including subsurface geoscientific perspectives of carbon geosequestration. This resource is a 21st Century guide for exploration geologists, geoscience students at postgraduate level and above, and petrophysicists working in the oil and gas industry. - Covers the latest and most effective technologies in reservoir characterization, including Avo analysis, AVAz inversion, wave field separation and Machine Learning techniques - Provides a balanced blend of both theoretical and practical approaches for solving challenges in reservoir characterization - Includes detailed industry-standard practical workflows, along with code structures for algorithms and practice exercises
Book Synopsis Reservoir characterization using single-well tracer tests by : Luiz Eraldo Araujo Ferreira
Download or read book Reservoir characterization using single-well tracer tests written by Luiz Eraldo Araujo Ferreira and published by . This book was released on 1992 with total page 1306 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Reservoir Characterization by : Larry Lake
Download or read book Reservoir Characterization written by Larry Lake and published by Elsevier. This book was released on 2012-12-02 with total page 680 pages. Available in PDF, EPUB and Kindle. Book excerpt: Reservoir Characterization is a collection of papers presented at the Reservoir Characterization Technical Conference, held at the Westin Hotel-Galleria in Dallas on April 29-May 1, 1985. Conference held April 29-May 1, 1985, at the Westin Hotel—Galleria in Dallas. The conference was sponsored by the National Institute for Petroleum and Energy Research, Bartlesville, Oklahoma. Reservoir characterization is a process for quantitatively assigning reservoir properties, recognizing geologic information and uncertainties in spatial variability. This book contains 19 chapters, and begins with the geological characterization of sandstone reservoir, followed by the geological prediction of shale distribution within the Prudhoe Bay field. The subsequent chapters are devoted to determination of reservoir properties, such as porosity, mineral occurrence, and permeability variation estimation. The discussion then shifts to the utility of a Bayesian-type formalism to delineate qualitative ""soft"" information and expert interpretation of reservoir description data. This topic is followed by papers concerning reservoir simulation, parameter assignment, and method of calculation of wetting phase relative permeability. This text also deals with the role of discontinuous vertical flow barriers in reservoir engineering. The last chapters focus on the effect of reservoir heterogeneity on oil reservoir. Petroleum engineers, scientists, and researchers will find this book of great value.
Book Synopsis Innovative Techniques for the Description of Reservoir Heterogeneity Using Tracers. Second Technical Annual Progress Report, October 1991--September 1992 by :
Download or read book Innovative Techniques for the Description of Reservoir Heterogeneity Using Tracers. Second Technical Annual Progress Report, October 1991--September 1992 written by and published by . This book was released on 1992 with total page 99 pages. Available in PDF, EPUB and Kindle. Book excerpt: This second annual report on innovative uses of tracers for reservoir characterization contains four sections each describing a novel use of oilfield tracers. The first section describes and illustrates the use of a new single-well tracer test to estimate wettability. This test consists of the injection of brine containing tracers followed by oil containing tracers, a shut-in period to allow some of the tracers to react, and then production of the tracers. The inclusion of the oil injection slug with tracers is unique to this test, and this is what makes the test work. We adapted our chemical simulator, UTCHEM, to enable us to study this tracer method and made an extensive simulation study to evaluate the effects of wettability based upon characteristic curves for relative permeability and capillary pressure for differing wetting states typical of oil reservoirs. The second section of this report describes a new method for analyzing interwell tracer data based upon a type-curve approach. Theoretical frequency response functions were used to build type curves of ''transfer function'' and ''phase spectrum'' that have dimensionless heterogeneity index as a parameter to characterize a stochastic permeability field. We illustrate this method by analyzing field tracer data. The third section of this report describes a new theory for interpreting interwell tracer data in terms of channeling and dispersive behavior for reservoirs. Once again, a stochastic approach to reservoir description is taken. The fourth section of this report describes our simulation of perfluorocarbon gas tracers. This new tracer technology developed at Brookhaven National Laboratory is being tested at the Elk Hills Naval Petroleum Reserve No. 1 in California. We report preliminary simulations made of these tracers in one of the oil reservoirs under evaluation with these tracers in this field. Our compostional simulator (UTCOMP) was used for this simulation study.
Book Synopsis An Investigation of Partitioning Tracers for Characterizing Geothermal Reservoirs and Predicting Enthalpy Production by : Xingru Wu
Download or read book An Investigation of Partitioning Tracers for Characterizing Geothermal Reservoirs and Predicting Enthalpy Production written by Xingru Wu and published by . This book was released on 2006 with total page 304 pages. Available in PDF, EPUB and Kindle. Book excerpt: A tracer selection protocol was developed after reviewing related literature of tracer applications and doing systematic simulations of tracer injection. An important conclusion is that for superheated geothermal reservoir, the partition coefficient (the K value) of the geothermal tracer should be high in order to get early information about reservoir characterization and liquid breakthrough.
Book Synopsis Modeling and application of tracers for reservoir characterization by : Vichai Maroongroge
Download or read book Modeling and application of tracers for reservoir characterization written by Vichai Maroongroge and published by . This book was released on 1994 with total page 714 pages. Available in PDF, EPUB and Kindle. Book excerpt:
Book Synopsis Dynamic Reservoir Characterization Of Naturally Fractured Reservoirs From An Inter-Well Tracer Test by : Ufuk Kilicaslan
Download or read book Dynamic Reservoir Characterization Of Naturally Fractured Reservoirs From An Inter-Well Tracer Test written by Ufuk Kilicaslan and published by . This book was released on 2014 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: After field redevelopment in the Sherrod Unit of the Spraberry Trend Area, an inter-well tracer test was conducted at the field scale in order to understand the fracture system, which forms preferential flow paths for better management of waterflooding. The test consisted of 13 injection wells and more than 110 producing wells that were sampled, with each injector having its own unique tracer. A wide range of tracer responses was observed in terms of tracer recovery, breakthrough time, and tracer velocity. Additional noise on tracer data was noticed due to reinjection of produced water. In this study, a comprehensive workflow is presented for dynamic reservoir characterization of naturally fractured reservoirs from an inter-well tracer test by incorporation of analytical interpretation, streamline simulation, and streamline-based optimization techniques. Categorized tracer responses were mapped according to analytical analysis, and dominating flow trends were detected in E-W and NE-SW directions before the simulation study. The constructed three-phase, dual-porosity model was simulated by a streamline simulator. Certain parameters in the model were modified based on high tracer response until a reasonable match was obtained for an inverted nine-spot pattern and breakthrough time of the injected tracer. Once the model became capable of matching historical field production, a 1-year prediction run was conducted for optimization. Cumulative oil production was increased by 8,000 bbl by allocating more water toward efficient producers, and 10,000 bbl less water was produced for the optimized case. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/151965
Book Synopsis Interpretation, Analysis and Design of Inter-well Tracer Tests in Naturally Fractured Reservoirs by : Aymen Abduljalil Alramadhan
Download or read book Interpretation, Analysis and Design of Inter-well Tracer Tests in Naturally Fractured Reservoirs written by Aymen Abduljalil Alramadhan and published by . This book was released on 2013 with total page 311 pages. Available in PDF, EPUB and Kindle. Book excerpt: In order to understand the complex fracture network that controls water movement in Sherrod Area of Spraberry Field in West Texas and to better manage the on-going waterflood performance, a field scale inter-well tracer test was implemented. This test presents the largest inter-well tracer test in naturally fractured reservoirs reported in the industry and includes the injection of 13 different tracers and sampling of 110 producers in an area covering 6533 acres. Sherrod tracer test generated a total of 598 tracer responses from 51 out of the 110 sampled producers. Tracer responses showed a wide range of velocities from 14 ft/day to ultra-high velocities exceeding 10,000 ft/day with same-day tracer breakthrough. Re-injection of produced water has caused the tracers to be re-injected and added an additional challenge to diagnose and distinguish tracer responses affected by water recycling. Historical performance of the field showed simultaneous water breakthrough of a large number of wells covering entire Sherrod area. This research investigate analytical, numerical, and inversion modeling approaches in order to categorize, history match, and connect tracer responses with water-cut responses with the objective to construct multiple fracture realizations based entirely on water-cut and tracers' profiles. In addition, the research highlight best practices in the design of inter-well tracer tests in naturally fractured reservoirs through lessons learned from Sherrod Area. The large number of tracer responses from Sherrod case presents a case of naturally fractured reservoir characterization entirely based on dynamic data. Results indicates that tracer responses could be categorized based on statistical analysis of tracer recoveries of all pairs of injectors and producers with each category showing distinguishing behavior in tracers' movement and breakthrough time. In addition, it showed that tracer and water-cut responses in the field are dominantly controlled by the fracture system revealing minimum information about the matrix system. Numerical simulation studies showed limitation in dual porosity formulation/solvers to model tracer velocities exceeding 2200 ft/day. Inversion modeling using Gradzone Analysis showed that east and north-west of Sherrod have significantly lower pore volume compared to south-west. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/151192
Book Synopsis Practical Reservoir Engineering and Characterization by : Richard O. Baker
Download or read book Practical Reservoir Engineering and Characterization written by Richard O. Baker and published by Gulf Professional Publishing. This book was released on 2015-04-30 with total page 535 pages. Available in PDF, EPUB and Kindle. Book excerpt: Practical Reservoir Characterization expertly explains key technologies, concepts, methods, and terminology in a way that allows readers in varying roles to appreciate the resulting interpretations and contribute to building reservoir characterization models that improve resource definition and recovery even in the most complex depositional environments. It is the perfect reference for senior reservoir engineers who want to increase their awareness of the latest in best practices, but is also ideal for team members who need to better understand their role in the characterization process. The text focuses on only the most critical areas, including modeling the reservoir unit, predicting well behavior, understanding past reservoir performance, and forecasting future reservoir performance. The text begins with an overview of the methods required for analyzing, characterizing, and developing real reservoirs, then explains the different methodologies and the types and sources of data required to characterize, forecast, and simulate a reservoir. - Thoroughly explains the data gathering methods required to characterize, forecast, and simulate a reservoir - Provides the fundamental background required to analyze, characterize, and develop real reservoirs in the most complex depositional environments - Presents a step-by-step approach for building a one, two, or three-dimensional representation of all reservoir types
Book Synopsis Temperature-sensitive Tracers for Fractured Geothermal Reservoir Characterization by : Morgan F. Ames
Download or read book Temperature-sensitive Tracers for Fractured Geothermal Reservoir Characterization written by Morgan F. Ames and published by . This book was released on 2016 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: One of the most significant open problems in geothermal reservoir engineering is the development of a reliable and accurate method to predict thermal breakthrough. Such a method would enable more informed decisions to be made regarding reservoir management. Methods developed at present include analytical models and solute tracers, both of which have limitations. The use of particles as temperature-sensitive tracers is a promising approach due to the high degree of control of the physical and chemical properties of nanomaterials and micromaterials. Additionally, particles experience less matrix diffusion than solute tracers and tend to stay in high velocity fluid streamlines, which results in earlier particle breakthrough in the absence of significant particle deposition. These properties could potentially be exploited to infer temperature and measurement location, which could in turn provide useful information about thermal breakthrough. In order to assess whether particle tracers can provide more useful information about future thermal behavior of reservoirs than existing solute tracers, models were developed for both solute tracers and particle tracers. Three existing solute tracer types were modeled: conservative solute tracers (CSTs), reactive solute tracers with temperature-dependent reaction kinetics (RSTs), and sorbing solute tracers that sorb reversibly to fracture walls (SSTs). Additionally, three particle tracers which have not been developed in practice were modeled: dye-releasing tracers (DRTs) that release a solute dye at a specified temperature threshold, threshold nanoreactor tracers (TNRTs) with an encapsulated reaction that does not begin until a specified temperature threshold is reached, and temperature-time tracers (TTTs) capable of recording detailed temperature-time histories of each particle. In this study, TTTs represent the most informative tracer with respect to thermal breakthrough. These models were used in the context of an inverse problem in which synthetic tracer data were calculated for several "true" discrete fracture networks. Next, computational optimization was used to match these data by adjusting fracture location, length, and orientation for a variable number of fractures. Finally, the thermal behaviors of the fracture networks with the best fits to the data were compared to those of the true fracture networks, and the tracers were ranked according to their forecasting ability. Overall, thermal breakthrough forecast error was found to increase with fracture network complexity. However, in all cases, all tracers forecasted thermal breakthrough with unrealistic accuracy. This is partly due to neglecting thermal interference between closely spaced fractures in the thermal model. In all three cases, CSTs were found to be the least informative tracer type because they are insensitive to temperature. SSTs were also modeled as insensitive to temperature in this work, but they performed better than CSTs because sorption is sensitive to surface area, which is also closely related to a reservoir's thermal performance. In order to fully understand the relative informativity of these solute and particle tracers, a second study was performed using a uniform parallel fracture reservoir model that accounts for interference between fractures in both thermal and tracer transport. In this study, a seventh type of tracer test was also considered in which all three solute tracer types (CSTs, RSTs, and SSTs) were used simultaneously to gain the benefits of all three tracer types. This tracer type was designated ALLSOL, which is short for "all solutes." As with the discrete fracture network modeling study, synthetic data were generated and matched using optimization, after which thermal breakthrough forecasts were calculated. The decision variables used in optimization were the number of fractures and fracture length, width, aperture, and spacing. Two inverse problem scenarios with different fracture spacings were examined: 15 meter spacing and 5 meter spacing. In both scenarios, all individual solute tracers had significant error, particle tracers and ALLSOL forecasted thermal breakthrough more accurately than individual solute tracers, and ALLSOL had slightly more accurate forecasts than particle tracers. In the 15 meter spacing scenario, both RST and TNRT had very inaccurate forecasts because the temperature distribution is somewhat insensitive to fracture spacing at early time when fracture spacing is sufficiently large. This resulted in good matches and small objective function values for inaccurate estimates of fracture spacing. In order to determine if other tracers besides RST and TNRT are insensitive to spacing at early time when spacing is sufficiently large, the objective function values of all tracer types were evaluated using the optimal solution for TNRT in the 15 meter spacing scenario. Low objective function values and good fits to the data were observed for every tracer type except for TTT, indicating that TTT is the only tracer type considered that is capable of detecting differences in spacing at early time when the true fracture spacing is large. This is because the temperature is measured directly by the TTT rather than inferring the temperature from the return curve, as is the case for all other tracer types. In the 5 meter spacing case, the RST had a very inaccurate thermal breakthrough forecast because its return curve has a nonunique relationship with the temperature distribution (i.e. the RST return curve was matched by a reservoir with a significantly different temperature distribution from the true reservoir, which happened to result in the same amount of reaction). Forecast error was generally larger in the uniform parallel fracture modeling scenarios than in the discrete fracture network modeling scenarios. This demonstrates the importance of accounting for thermal interference in temperature-sensitive tracer modeling.
Book Synopsis DNA-based Tracers for Fractured Reservoir Characterization by : Yuran Zhang
Download or read book DNA-based Tracers for Fractured Reservoir Characterization written by Yuran Zhang and published by . This book was released on 2020 with total page pages. Available in PDF, EPUB and Kindle. Book excerpt: A thorough understanding of the subsurface fracture network is crucial for the effective exploitation and management of geothermal energy, unconventional hydrocarbon resources, groundwater reservoirs, etc. While conventional tracer technology is a useful tool to characterize the complex network of flowpaths in geologic reservoirs, tracers are limited in unique variations and hence insufficient for characterizing reservoirs with a large number of wells. In addition, conventional tracer testing only provides a "snapshot" of the flowpath properties which may be inadequate for reservoirs that are subjected to changes. This research sought to resolve the limitations of conventional tracer testing by exploring novel, DNA-based tracer candidates. DNA's infinite number of unique sequences and hence great degree of specificity makes it a promising tracer candidate for improved subsurface characterization. We first investigated the use of uniquely designed, synthetic DNA fragments as injected tracers. The method to measure target-specific DNA tracer concentration is described. The effect of DNA sequence, fragment length and porous medium on DNA transport was studied to provide guidance to potential field applications and data interpretation. It was found that DNA transport was not affected by DNA sequence (i.e. the arrangement of nucleotides). The length of DNA fragments does not affect the shape of the tracer return curve, but does affect tracer mass recovery. Shorter DNA appeared to be more prone to adsorption, while longer DNA appeared to be more prone to size exclusion effect. We then extended the concept of DNA-based tracers towards the genomic DNA of fluid-associated microorganisms that naturally colonize a geologic reservoir. Instead of targeting just a few microbes, we proposed taking advantage of the entire microbial community population in a reservoir fluid sample as unique signatures pinpointing the origins of fluids. We tested this method at a mesoscale enhanced geothermal system (EGS) testbed at Sanford Underground Research Facility (SURF) by sampling indigenous fluids produced from separate fractures and analyzing their microbial community structure via high-throughput 16S rRNA gene amplicon sequencing. We found that hydraulically isolated fractures at our field site hosted distinct microbial community populations, demonstrating substantial microbial heterogeneity across fractures. However, locally within a fracture, the microbial community were relatively homogenized, serving as a unique natural tracer or "fingerprint" of the fracture. We demonstrated at our field site that sampling indigenous fluids from an undisturbed, newly developed reservoir could help us identify natural interwell connectivity when more than one well were drilled into the same natural fracture. Finally, building upon the idea of reservoir indigenous microbial populations as natural tracers, we investigated the potential of this novel data source in an actively circulating, dynamic reservoir. Again using the EGS testbed at SURF, we sampled the produced fluids from the reservoir that underwent long-term flow circulation. Sampling was conducted regularly in a 5-month time series and the microbial populations in the fluids were sequenced. We found that although the whole circulating reservoir were connected hydraulically, the difference in relative connectivity among fractures still allowed different flowing fractures to have different microbial community signatures. The long-term microbial monitoring at our site identified the switch of production zone of a borehole likely due to major changes in the fracture network. Changes in fracture network were also observed from microbial time-series data after a week-long injection halt, likely due to the reopened hydraulic fracture not restoring to its initial state. We thereby demonstrated that long-term microbial community monitoring in an active reservoir may effectively enable the direct observation of fracture network evolution. Such information is difficult to achieve via other reservoir diagnostic methods.
Book Synopsis Applied Techniques to Integrated Oil and Gas Reservoir Characterization by : Enwenode Onajite
Download or read book Applied Techniques to Integrated Oil and Gas Reservoir Characterization written by Enwenode Onajite and published by Elsevier. This book was released on 2021-04-09 with total page 439 pages. Available in PDF, EPUB and Kindle. Book excerpt: Over the past several years, there has been a growing integration of data – geophysical, geological, petrophysical, engineering-related, and production-related – in predicting and determining reservoir properties. As such, geoscientists now must learn the technology, processes, and challenges involved within their specific functions in order to optimize planning for oil field development. Applied Techniques to Integrated Oil and Gas Reservoir Characterization presents challenging questions encountered by geoscientists in their day-to-day work in the exploration and development of oil and gas fields and provides potential solutions from experts. From basin analysis of conventional and unconventional reservoirs, to seismic attributes analysis, NMR for reservoir characterization, amplitude versus offset (AVO), well-to-seismic tie, seismic inversion studies, rock physics, pore pressure prediction, and 4D for reservoir monitoring, the text examines challenges in the industry as well as the techniques used to overcome those challenges. This book includes valuable contributions from global industry experts: Brian Schulte (Schiefer Reservoir Consulting), Dr. Neil W. Craigie (Saudi Aramco), Matthijs van der Molen (Shell International E&P), Dr. Fred W. Schroeder (ExxonMobil, retired), Dr. Tharwat Hassane (Schlumberger & BP, retired), and others. - Presents a thorough understanding of the requirements of various disciplines in characterizing a wide spectrum of reservoirs - Includes real-life problems and challenging questions encountered by geoscientists in their day-to-day work, along with answers from experts working in the field - Provides an integrated approach among different disciplines (geology, geophysics, petrophysics, and petroleum engineering) - Offers advice from industry experts to geoscience students, including career guides and interview tips
Book Synopsis Reservoir Characterization II by : Larry W. Lake
Download or read book Reservoir Characterization II written by Larry W. Lake and published by Academic Press. This book was released on 1991-04-28 with total page 752 pages. Available in PDF, EPUB and Kindle. Book excerpt: Intended for petroleum engineers, geologists and hydrologists, this book provides a detailed survey of the current practices, problems, research and trends in the field of reservoir characterization. Topics discussed include mesoscopic, macroscopic and megascopic scales.
