1000d Countersunk Head D Slot Recess Corrosion Resisting Steel Bolts Unified Threads Strength Class 880 Mpa For Aircraft

Author : Richard T. Barrett
Publisher :
ISBN 13 : 9781463771232
Total Pages : 100 pages
Book Rating : 4.7/5 (712 download)

DOWNLOAD NOW!

Download or read book Fastener Design Manual written by Richard T. Barrett and published by . This book was released on 2011-07-27 with total page 100 pages. Available in PDF, EPUB and Kindle. Book excerpt: This manual was written for design engineers to enable them to choose appropriate fasteners for their designs. Subject matter includes fastener material selection, platings, lubricants, corrosion, locking methods, washers, inserts, thread types and classes, fatigue loading, and fastener torque. A section on design criteria covers the derivation of torque formulas, loads on a fastener group, combining simultaneous shear and tension loads, pullout load for tapped bales, grip length, head styles, and fastener strengths. The second half of this manual presents general guidelines and selection criteria for rivets and lockbolts. To the casual observer the selection of bolts, nuts, and rivets for a design should be a simple task. In reality it is a difficult task, requiring careful consideration of temperature, corrosion, vibration, fatigue, initial preload, and many other factors. The intent of this manual is to present enough data on bolt and rivet materials, finishes, torques, and thread lubricants to enable a designer to make a sensible selection for a particular design. Lockouts, washers, locking methods, inserts, rivets, and tapped holes arc also covered. Bolts can be made froni many materials, but most bolts are made of carbon steel, alloy steel, or stainless steel. Stainless steels include both iron- and nickel-based chromium alloys. Titanium and aluminum bolts have limited usage, primarily in the aerospace industry. Carbon steel is the cheapest and most common bolt material. Most hardware stores sell carbon steel bolts, which are usually zinc plated to resist corrosion_ The typical ultimate strength of this bolt material is 55 ksi. An alloy steel is a high-strength carbon steel that can be heat treated up to 300 ksi. However, it is not corrosion resistant and must therefore have some type of coating to protect it from corrosion. Aerospace alloy steel fasteners are usually cadmium plated for corrosion protection_ Bolts of stainless steel (cREs) are available in a variety of alloys with ultimate strengths from 70 to 220 ksi. The major advantage of using CRES is that it normally requires no protective coating and has a wider service temperature range than plain carbon or alloy steels. A partial listing of bolt materials is given in table 1. The following precautions are to be noted: (1) The bolt plating material is usually the limiting factor on maximum service temperature. (2) Carbon steel and alloy steel are unsatisfactory (become brittle) at temperatures below -65 'F. (3) Hydrogen embrittlement is a problem with most common methods of plating, unless special procedures are used. (This subject is covered more fully in the corrosion section.) (4) Series 400 CRES contains only 12 percent chromium and thus will corrode in some environments, (5) The contact of dissimilar materials can create galvanic corrosion, which can become a major problem. (Galvanic corrosion is covered in a subsequent section of this manual.) Platings and Coatings Most plating processes are electrolytic and generate hydro-gen. Thus, most plating processes require baking after plating at a temperature well below the decomposition temperature of the plating material to prevent hydrogen ernhrittlernent. However, heating the plating to its decomposition temperature can generate free hydrogen again. Thus, exceeding the safe operating temperature of the plating can cause premature fastener failure due to hydrogen embrittlement as well as loss of corrosion protection. (A summary of platings and coatings is given in table II.) Cadmium Plating The most common aerospace fastener plating material is cadmium. Plating is done by electrodeposition and is easy to accomplish. However, cadmium-plated parts must be baked at 375 "F for 23 hours, within 2 hours after plating, to prevent hydrogen embrittlement. Since cadmium melts at 600 "F, its useful service temperature limit is 450 'F.